Post on 09-Apr-2018
8/7/2019 manual grabadora ICDUX200
1/124
4-156-546-71(2)
2009 Sony Corporation
IC Recorder
Operating Instructions
Printed in China
ICD-UX200/UX300/UX200F/UX300F
Getting Started
Basic Operations
Other Recording Operations
Other Playback Operations
Editing MessagesListening to the FM Radio
About the Menu Function
Utilizing Your Computer
Additional InformationTroubleshooting
8/7/2019 manual grabadora ICDUX200
2/124
2GB
Owner's RecordThe model number is located at the rear panel and the
serial number is located inside the battery
compartment. Record these numbers in the space
provided below. Refer to these numbers wheneveryou call upon your Sony dealer regarding this
product.
Model No. __________________________________
Serial No. __________________________________
FOR UNITED STATESCUSTOMERS. NOT APPLICABLEIN CANADA, INCLUDING IN THEPROVINCE OF QUEBEC.POUR LES CONSOMMATEURSAUX TATS-UNIS. NONAPPLICABLE AU CANADA, YCOMPRIS LA PROVINCE DE
QUBEC.For the customers in the UnitedStatesThe following FCC statement applies only to the
version of this model manufactured for sale in the
USA. Other versions may not comply with FCC
technical regulations.
INFORMATIONThis equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or televisionreception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
You are cautioned that any changes or modifications
not expressly approved in this manual could void your
authority to operate this equipment.
If you have any questions about this product, you maycall: Sony Customer Information Service Center 1-
800-222-7669 or http://www.sony.com/
8/7/2019 manual grabadora ICDUX200
3/124
3GB
Notice for the customers inCanadaThis class B digital apparatus complies with Canadian
ICES-003.
For the customers in the USAand Canada
RECYCLING NICKEL METAL HYDRIDEBATTERIESNickel metal hydride batteries are
recyclable.You can help preserve our
environment by returning your used
rechargeable batteries to the
collection and recycling location
nearest you.
For more information regarding recycling of
rechargeable batteries, call toll free 1-800-822-8837,
or visit http://www.rbrc.org/.
Caution: Do not handle damaged or leaking nickel
metal hydride batteries.
Declaration of ConformityTrade Name : SONY
Model : ICD-UX200/UX300
Responsible Party : Sony Electronics Inc.Address : 16530 Via Esprillo,
San Diego, CA 92127 USA
Telephone Number : 858-942-2230
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
The recorded music is limited to private use only.
Use of the music beyond this limit requires
permission of the copyright holders.
Sony is not responsible for incomplete recording/
downloading or damaged data due to problems ofthe IC recorder or computer.
Depending on the types of the text and characters,
the text shown on the IC recorder may not be
displayed properly on device. This is due to:
The capacity of the connected IC recorder.
The IC recorder is not functioning normally.
Content information is written in the language
or the character that is not supported by the ICrecorder.
8/7/2019 manual grabadora ICDUX200
4/1244GB
Table of Contents
Getting StartedStep 1: Checking the Contents of thePackage .....................................................7
Index to parts and controls ...................8
Step 2: Recharging the Battery .................9
When to charge/replace the battery .... 11
Step 3: Turning the IC Recorder On .......12Turning the power on .........................12
Turning the power off .........................12
Step 4: Setting the Clock ........................13
Setting the clock after recharging thebattery .................................................13
Setting the clock using the menu ........13
Step 5: Setting the Language to Be Usedin the Display Window ...........................15
Preventing Accidental Operation(HOLD) ...................................................17
Locking the buttons ............................17
Unlocking the buttons .........................17
Basic OperationsRecording .......................................18
Listening .........................................22
Erasing ............................................26
Other Recording OperationsChanging the Recording Settings ............28
Selecting the recording mode .............28
Setting the microphone sensitivity ......29
Cutting out low frequency the LCF function ..............................31
Starting to record automatically inresponse to sound the VOR function .............................32
Operating during Recording ....................34
Monitoring the recording ....................34
Dividing a message duringrecording .............................................34
Recording via Other Devices ..................36Recording with an externalmicrophone .........................................36
Recording from other equipment ........37
Other Playback Operations
Changing the Playback Method ..............42Convenient playback methods ............42
Adjusting the playback speed the DPC function .............................43
Changing the Playback Settings ..............45
Selecting the playback mode ..............45
Making the human voice clearer
the noise cut function .......................47Selecting the sound effect ...................48
8/7/2019 manual grabadora ICDUX200
5/124
5GB
Playing Back a Message at a DesiredTime with an Alarm ................................50
Playback via Other Devices ....................53
Recording with other equipment ........ 53
Editing MessagesErasing All Messages in a Folder ...........55
Moving a Message to a DifferentFolder ......................................................56
Dividing a Message into Two .................58
Listening to the FM RadioTuning in an FM Radio Station ..............60
Switching the FM radio outputbetween speaker and headphones .......61
Switching the receiver sensitivity ofthe FM radio .......................................62
Recording FM broadcasts ...................63
Presetting FM Radio StationsAutomatically .........................................64
Switching the scanning sensitivity ..... 65
Presetting FM Radio StationsManually .................................................67
Listening to a Preset Radio Station .........68
Erasing Preset FM Radio Stations ..........69
About the Menu Function
Making Settings for the Menu ................71Menu Settings .........................................72
Utilizing Your ComputerUsing the IC Recorder with YourComputer .................................................83
System requirements for yourcomputer .............................................83
Connecting the IC recorder to yourcomputer .............................................84
Construction of folders and files .........85
Copying Messages from the ICRecorder to Your Computer to
Save Them ...............................................87Copying Music Files from YourComputer to the IC Recorder andPlaying Them Back .................................88
Copying a music file from yourcomputer to the IC recorder(drag and drop) ...................................88
Enjoying the music files more ............90Using the IC Recorder as USB Memory Data Storage Function ..........................91
Using Voice Recognition Software .........92
Introducing the voice recognitionsoftware ...............................................92
Creating a user file adapted to your
recorded speech (Training) .................92Disconnecting the IC Recorder fromYour Computer .......................................94
Additional InformationUsing a USB AC Adaptor(not supplied) ..........................................95
8/7/2019 manual grabadora ICDUX200
6/124
6GB
Disconnecting the IC recorder fromthe AC outlet .......................................96
Precautions ..............................................97
Specifications ..........................................99System requirements ..........................99
Design and specifications .................100
Battery life ........................................103
Troubleshooting
Troubleshooting ....................................105Error Messages .....................................112
System Limitations ...............................115
Display Window Guide ........................116
Index .....................................................119
Trademarks ...........................................122
8/7/2019 manual grabadora ICDUX200
7/124
7GB
GettingStarted
Getting Started
Step 1: Checking the Contents of thePackage
IC Recorder (1)
Remove the film on the display windowbefore you use the IC recorder.
NH-AAA (size AAA) rechargeablebattery (1)
Stereo headphones (1)
USB connection support cable (1)
If the IC recorder cannot be connected to acomputer directly, use the supplied USB
connection support cable.
Battery case (1)
Operating Instructions
You are cautioned that any changes or
modifications not expressly approved in thismanual could void your authority to operate
this equipment.
8/7/2019 manual grabadora ICDUX200
8/124
8GB
Index to parts and controls
Front
A Operation indicator
B Built-in microphones (stereo)
C Display window
D x STOP button
Ez
REC (record)/PAUSE buttonF Control button (v, V /. (review/fast
backward), > (cue/fast forward))
G N (play)/ENT (enter) button*
H (folder) button
I MENU button
J m (microphone) jack*K i (headphone) jack
L ERASE button
M VOL (volume) +*/ button
N (repeat) A-B button
O DIVIDE button
Rear
P Strap hole (A strap is not supplied.)
Q Speaker
R USB slide leverS HOLD/POWER switch
T DPC (SPEED CTRL) switch
U Battery compartment
* These buttons and the jack have a tactile dot.
Use it as a reference point for operations, or
to identify each terminal.
8/7/2019 manual grabadora ICDUX200
9/124
9GB
GettingStarted
Step 2: Recharging the Battery
Remove the film on the display windowbefore you use the IC recorder.
Connect the IC recorder to a running
computer, and charge the battery until the
battery indicator indicates .
When you use the IC recorder for the first
time, or after you have not used the IC
recorder for a certain period of time, charge
the battery continuously until is
displayed.
It takes about 3 hours and 30 minutes to
fully charge exhausted battery.*1
You can also charge the battery by using an
AC-U50A USB AC adaptor (not supplied),
etc.
1 Insert a rechargeable battery.Slide and lift the battery compartment
lid, insert one NH-AAA rechargeable
battery with correct polarity, and closethe lid.
2Insert the USB connector of the ICrecorder into the USB port of a
computer.
Slide the USB lever on the back of the IC
recorder in the direction of the arrow,
and insert the USB connector into the
USB port of a running computer.*2
Computer
IC recorder
To USB port
8/7/2019 manual grabadora ICDUX200
10/124
10GB
While the battery is charging,
Connecting and the battery indicator
are displayed in an animation.
3 Disconnect the IC recorder from yourcomputer.
Follow the procedures below; otherwise,
when the IC recorder contains data files,
the files may be damaged or become
unplayable.
1 Perform the following operation onyour computer.
On the Windows screen, left-click the
icon at the bottom of the desktop ofthe computer.
t Left-click Safely remove USBMass Storage Device.
The icon can be different on different
operating systems.On the Macintosh screen, drag the
IC RECORDER on the desktop to
Trash and drop it there.
For details on disconnecting the IC
recorder from your computer, refer to
the operating instructions suppliedwith your computer.
2 Make sure that the display of the IC
recorder turns off.
3 Disconnect the IC recorder from theUSB port of the computer, and slide
the USB lever in the direction of the
arrow to retract the USB connector.
*1 This is an approximation for the time ittakes to charge from no remaining battery
power to full battery power at room
temperature. It varies depending on the
remaining power and the condition of thebattery. It also takes more time if the
temperature of the battery is low, or if the
battery is charged while you are transferringdata to the IC recorder.
*2 If the IC recorder cannot be connected to a
computer directly, use the supplied USB
connection support cable.
Battery indicator
8/7/2019 manual grabadora ICDUX200
11/124
11GB
GettingStarted
P NoteIf the battery indicator is not displayed in an
animation, charging has not been done
properly. See Troubleshooting on page 108.
When using a fully chargedbattery or an LR03 (size AAA)alkaline batteryFollow the step 1.
z Tips Do not use manganese battery for this IC
recorder.
When replacing the battery, messages
recorded or alarm settings are not erased
even when you remove the battery.
When replacing the battery, the clock
continues moving for about 3 minutes after
you remove the battery.
When to charge/replace thebattery
The battery indicator on the display shows
the battery condition.
Battery remain indication
: Charge the rechargeable battery or
replace the old battery with a new
one.
m
: Low Battery appears and the IC
recorder will stop operation.
8/7/2019 manual grabadora ICDUX200
12/124
12GB
Step 3: Turning the IC Recorder On
Turning the power on
Slide the HOLD/POWER switch in the
direction of POWER for more than 1
second. The IC recorder is turned on, and
Accessing... is displayed.
Turning the power offSlide the HOLD/POWER switch in the
direction of POWER for more than 2
seconds, and Power Off is displayed.
z Tips
When you are not going to use the ICrecorder for a long time, we recommend to
turn off the IC recorder.
When you leave the IC recorder withoutattempting an operation for a certain length
of time, the auto power off function will take
effect. (The length of time before auto power
off is set to 10min when you purchase the
IC recorder.) You can select the length of
time before auto power off in the menu(page 81).
8/7/2019 manual grabadora ICDUX200
13/124
13GB
GettingStarted
Step 4: Setting the Clock
You need to set the clock to use the alarm
function or record the date and time.
Clock setting display appears when you
insert battery for the first time, or when youinsert a battery after the IC recorder has
been without battery for more than 3
minutes, Set Date&Time appears, and
then the year section flashes in the display
window.
Setting the clock afterrecharging the battery
1 Press v or V on the control button to setthe year, month, day, hour, and minute in
sequence, and then press N/ENT.
2 Press x STOP to return to the stop modedisplay.
Setting the clock using themenu
While the IC recorder is in the stop mode,
you can set the clock using the menu.
1 Select Date&Time in the menu.
1 Press MENU to enter the menu mode.
x STOP
N/ENT
MENU
v, V
8/7/2019 manual grabadora ICDUX200
14/124
14GB
The menu mode window will be
displayed.
2 Press v or V on the control button to
select Detail Menu, and then pressN/ENT.
3 Press v or V on the control button to
select Date&Time, and then pressN/ENT.
2 Press v or V on the control button toselect 09y1m1d, and then press N/
ENT.
3 Press v or V on the control button to setthe year, month, day, hour, and minute in
sequence, and then press N/ENT.
4 Press x STOP to return to the stop modedisplay.
P NoteIf you do not press N/ENT within 1 minute
of entering the clock setting data, the clock
setting mode is cancelled and the window will
return to the display of the stop mode.
To display the current date andtimePress x STOP to display the current date
and time.
8/7/2019 manual grabadora ICDUX200
15/124
15GB
GettingStarted
Step 5: Setting the Language to Be Used inthe Display Window
You can select the language to be used for
messages, menus, folder names, file names,
etc. from 3 languages.
1 Press MENU to enter the menu mode.The menu mode window will be
displayed.
2 Press v or V on the control button toselect Detail Menu, and then press N/
ENT.
3 Press v or V on the control button toselect Language, and then press N/
ENT.
4 Press v or V on the control button toselect the language that you want to use,
and then press N/ENT.
N/ENT
MENU
v, V
8/7/2019 manual grabadora ICDUX200
16/124
16GB
You can select the following languages.
English, Espaol (Spanish), Franais
(French)
8/7/2019 manual grabadora ICDUX200
17/124
17GB
GettingStarted
Preventing Accidental Operation (HOLD)
Locking the buttons
Slide the HOLD/POWER switch in the
direction of HOLD.
HOLD will appear indicating for approx.
3 seconds that all the functions of the
buttons are locked.
Unlocking the buttonsSlide the HOLD/POWER switch towards
the center so that all buttons will be
unlocked.
P NoteWhen the HOLD function is activated during
recording, all the functions of the buttons are
locked to prevent accidental operation. To stop
recording, cancel the HOLD function first.
z TipEven if the HOLD function is activated, you
can stop the alarm playback by pressing any
button. (You cannot stop normal playback.)
Basic Operations
8/7/2019 manual grabadora ICDUX200
18/124
18GB
Basic Operations
Recording
P Note Before making a recording, exit HOLD mode and turn on the power.
Selecting a folder
1 Press to display the folder selection window.
2 Press v or V on the control button to select the folder inwhich you want to record messages
( FOLDER01-10).
There are 10 folders already available when you
purchase the IC recorder.
3 Press N/ENT.
v
V
N/ENT
8/7/2019 manual grabadora ICDUX200
19/124
19GB
BasicOperations
Starting to record
To stop recording
Note while accessingThe IC recorder is recording data and saving it in memory when Accessing... appears on
the display. While the IC recorder is accessing data, do not remove the battery or connect or
disconnect the USB AC adaptor (not supplied). Doing so may damage the data.
1 Press z REC/PAUSE in the stop mode.
The operation indicator lights in red.You do not need to press and hold z REC/PAUSE
while recording.
The new message will be automatically recorded after
the last recorded message.
2 Turn the built-in microphones in the direction of thesource to be recorded.
1 Press x STOP.Accessing... appears on the display and the IC
recorder stops at the beginning of the current recording.
Operationindicator
z REC/PAUSE
Built-inmicrophones
x STOP
8/7/2019 manual grabadora ICDUX200
20/124
20GB
Other operations
z Tips
Messages recorded using this IC recorder will be recorded as MP3 files. You can record up to 99 messages in each folder.
Before you start recording, we recommend you make a trial recording first, or monitor the
recording (page 34).
P Notes Noise may be recorded if an object, such as your finger, etc., accidentally rubs or scratches the IC
recorder during recording. Before making a recording, be sure to check the battery indicator (page 11).
pause recording* Press z REC/PAUSE. During recording pause, the operationindicator flashes in red and flashes in the display window.
release pause and resumerecording
Press z REC/PAUSE again. Recording resumes from that point. (Tostop recording after pausing recording, press x STOP.)
review the currentrecording instantly
Press N/ENT. Recording stops and playback starts from thebeginning of the message just recorded.
review during recording Press and hold . on the control button during recording orrecording pause. Recording stops and you can search backwards
while listening to fast playback sound. After you release . on thecontrol button, playback starts from that point.
* 1 hour after you pause recording, recording pause is automatically released and the IC recorder entersthe stop mode.
8/7/2019 manual grabadora ICDUX200
21/124
21GB
BasicOperations
8/7/2019 manual grabadora ICDUX200
22/124
22GB
Listening
P Note Before playback starts, exit HOLD mode and turn on the power.
To start playback
1 Press .
2 Press v or V on the control button to select the folder.
3 Press > on the control button.
4 Press v or V on the control button to select the message
you want to play.
v
V
>
v
V
8/7/2019 manual grabadora ICDUX200
23/124
23GB
BasicOperations
To stop playback
5 Press N/ENT.Playback will start soon, and the operation indicator
will light in green. (When LED is set to OFF in the
menu (page 80), the operation indicator does not light.)
6 Press VOL +/ to adjust the volume.
1 Press x STOP.
Operationindicator
N/ENT
VOL +/
x STOP
8/7/2019 manual grabadora ICDUX200
24/124
24GB
Other operations
Display when playing back the messages
A File information
Press v or V on the control button to check the file information during playback.
A message recorded using the IC recorder is displayed as follows.
You can change the folder name, title, artist name, and/or file name using a computer.
stop at the current position(Playback Pause function)
Press N/ENT. To resume playback from that point, press N/ENTagain.
go back to the beginning ofthe current message
Press . on the control button once.*
go back to previousmessages
Press . on the control button repeatedly. (During the stop mode,keep the button pressed to go back the messages continuously.)
skip to the next message Press > on the control button once.*
skip to the succeedingmessages Press>
on the control button repeatedly. (During the stop mode,keep the button pressed to skip the messages continuously.)
* These operations are for when Easy Search is set to OFF (page 76).
: Folder name: FOLDER01-FOLDER10
: Title: Date_file number (e.g. 090101_001 or FM_090101_001)
: Artist name: My Recording
: File name: Date_file number (e.g. 090101_001 or FM_090101_001)
8/7/2019 manual grabadora ICDUX200
25/124
25GB
BasicOperations
B Counter information
You can select the display mode in the menu (page 77).
Elapsed time: Elapsed playback time of one message
Remaining time: The remaining time of the messageRecording date: Date recorded
Recording time: Time recorded
C Remaining recording time
Displays the remaining recording time in hours, minutes, and seconds.
If there is more than 10 hours time remaining, the time is displayed in hours.
If there is more than 10 minutes and less than 10 hours time remaining, the time isdisplayed in hours and minutes.
If there is less than 10 minutes time remaining, the time is displayed in minutes and
seconds.
8/7/2019 manual grabadora ICDUX200
26/124
26GB
Erasing
P Notes Once a recording has been erased, you cannot retrieve it.
Before erasing a message, exit HOLD mode and turn on the power.
Selecting a message and erasing it
1 Select the message you want to erase when the ICrecorder is in the stop or playback mode.
2 Press ERASE.Erase? appears with the message title.
3 Press v or V on the control button to select Execute.
ERASE
v
V
8/7/2019 manual grabadora ICDUX200
27/124
27GB
BasicOperations
To cancel erasing
Erasing another messageProceed with the same steps again from the beginning.
Erasing a part of one messageDivide the message into two messages first (page 58), and then proceed with the same steps
from the beginning.
4 Press N/ENT.Erasing... appears in the display window and the
selected message will be erased.
When a message is erased, the remaining messages will
advance and be renumbered so that there will be no
space between messages.
1 Select Cancel in step 3 of Selecting a message anderasing it, and then press N/ENT.
N/ENT
N/ENT
Other Recording Operations
8/7/2019 manual grabadora ICDUX200
28/124
28GB
Changing the Recording Settings
Selecting the recordingmode
You can select the recording mode in the
menu when the IC recorder is in the stop
mode or the FM radio mode.
1 Press MENU to enter the menu mode.The menu mode window will be
displayed.
2 Press v or V on the control button toselect REC Mode, and then press N/
ENT.
3 Press v or V on the control button toselect ST, STSP, STLP, SP, or
LP, and then press N/ENT.
4 Press x STOP to exit the menu mode.
N/ENT
MENU
v, V
x STOP
8/7/2019 manual grabadora ICDUX200
29/124
2
8/7/2019 manual grabadora ICDUX200
30/124
30GB
2 Press v or V on the control button toselect Mic Sensitivity, and then press
N/ENT.
3 Press v or V on the control button toselect S-High , High ,Low , and then press N/ENT.
4 Press x STOP to exit the menu mode.
The microphone sensitivity is set to
High when you purchase the IC
recorder.
S-High To record a sound far awayfrom the IC recorder or a lowsound, such as a recordingmade in a spacious room.
High To record the sound of anormal conversation ormeeting, such as a recordingmade in a conference room orduring interviews.
Low To record dictation with a
microphone in front of yourmouth, a sound near the ICrecorder, or a loud sound.
2
8/7/2019 manual grabadora ICDUX200
31/124
31GB
OtherRecordingOperations
Cutting out low frequency the LCF function
When you set the LCF (Low Cut Filter)
function to ON in the stop or recording
mode, you cut out a low frequency to
reduce the roaring noise from wind, etc.;therefore you can record a message more
clearly.
1 Press MENU to enter the menu mode.The menu mode window will be
displayed.
2 Press v or V on the control button toselect LCF(Low Cut), and then press
N/ENT.
3 Press v or V on the control button to
select ON, and then press N/ENT.
The LCF function is set to OFF whenyou purchase the IC recorder.
4 Press x STOP to exit the menu mode.
To cancel the LCF functionSet LCF(Low Cut) to OFF in step 3.
N/ENT
MENU
v, V
x STOP
2
8/7/2019 manual grabadora ICDUX200
32/124
32GB
Starting to recordautomatically in response tosound the VOR function
You can set the VOR (Voice Operated
Recording) function to ON when the IC
recorder is stopped or is recording, to make
the IC recorder start recording when the ICrecorder detects sound, and pause when no
sound is heard, eliminating recording
during soundless periods.
1 Press MENU to enter the menu mode.
The menu mode window will bedisplayed.
2 Press v or V on the control button toselect VOR, and then press N/ENT.
3 Press v or V on the control button toselect ON, and then press N/ENT.
The VOR function is set to OFF when
you purchase the IC recorder.
4 Press x STOP to exit the menu mode.
5 Press z REC/PAUSE. and appear in the display
window.
The recording pauses when no sound is
detected and and flash.
When the IC recorder detects sound again,
the recording starts again.
x STOP
z REC/PAUSE
N/ENT
MENU
v,
V
T l h VOR f i
8/7/2019 manual grabadora ICDUX200
33/124
33GB
OtherRecordingOperations
To cancel the VOR functionSet VOR to OFF in step 3.
P Note
The VOR function is affected by the soundaround you. Set Mic Sensitivity in the menu
according to the recording conditions. If
recording is not satisfactory after you have
changed the microphone sensitivity, or for an
important recording, set VOR to OFF inthe menu.
O ti d i R di
8/7/2019 manual grabadora ICDUX200
34/124
34GB
Operating during Recording
Monitoring the recording
If you connect the supplied stereo
headphones to the i (headphone) jack
before you start, you can monitor therecording. You can adjust the monitoring
volume by pressing VOL +/, but the
recording level is fixed.
Dividing a message duringrecording
You can divide a message during recording
so that the message is divided into twoparts, and a new message number is added
to the newer part of the divided message.
Once a message is divided, you cannot
re-combine the divided messages.
i (headphone) jack
VOL +/
DIVIDE
1 P DIVIDE d i di
8/7/2019 manual grabadora ICDUX200
35/124
35GB
OtherRecordingOperations
1 Press DIVIDE during recording.Dividing... appears on the display and
the new message number is added at the
point you pressed the button. The
message will be recorded as two
messages, however recording continues
without stopping.
z Tip
You can divide the currently recorded messageduring recording pause.
P NoteWhen you divide a message into two, at the
point of division, the end of the first message
and the beginning of the second message may
be interrupted.
Message 1 Message 2 Message 3
v
Message is divided.
Message 2 and Message 3 arerecorded without stopping.
Recording via Other Devices
8/7/2019 manual grabadora ICDUX200
36/124
36GB
Recording via Other Devices
Recording with an externalmicrophone
1 Connect an external microphone to them (microphone) jack when the ICrecorder is in the stop mode.
Select Input appears in the display
window.
If Select Input is not displayed, set it inthe menu (page 82).
2 Press v or V on the control button toselect MIC IN, and then press N/
ENT.
3 Press x STOP to exit the menu mode.
4 Press z REC/PAUSE to start recording.The built-in microphones are
automatically cut off.If the input level is not strong enough,
adjust the microphone sensitivity on the
IC recorder.
When a plug in power type microphone
is connected, power is automatically
supplied to the microphone from the ICrecorder.
z Recommended microphonesYou can use the Sony ECM-CS10,
ECM-CZ10, ECM-DS70P, ECM-DS30Pelectret condenser microphone (not supplied).
v, V
Stereo microphone
x STOP
z REC/PAUSE
N/ENT
m (microphone) jack
Recording sound from a Recording from other
8/7/2019 manual grabadora ICDUX200
37/124
37GB
OtherRecordingOperations
Recording sound from atelephone or a cell phoneYou can use the ECM-TL1 headphone-type
electret condenser microphone (not
supplied) to record sound from a telephone
or a cell phone.
For details on how to make the connection,
refer to the operating instructions supplied
with the ECM-TL1 microphone.
P Notes After you have made the connection, checkthe sound quality of the conversation and the
recording level before you start recording.
If the beep of the telephone or a dial tone is
recorded, the conversation may be recorded
with lower level of sound. In this case, start
recording after the conversation has started. The VOR function may not work, depending
on the kind of telephone or the linecondition.
We assume no responsibility whatsoever for
any inconvenience, even if you cannotrecord a conversation using the IC recorder.
Recording from otherequipment
You can make music files without using the
computer by recording the sound from
other equipment connected to the ICrecorder.
z Tips Before you start recording, we recommend
you make a trial recording first.
If the input level is not strong enough,
connect the headphone jack (minijack,stereo) of other equipment to the
v, V
External equipment
x STOP
z REC/PAUSE
N/ENT
MENU
m (microphone) jack
m (microphone) jack of the IC recorder and
8/7/2019 manual grabadora ICDUX200
38/124
38GB
m (microphone) jack of the IC recorder andadjust the volume level on the piece of
equipment connected to the IC recorder.
To record using thesynchronized recording function
1 Press MENU to enter the menu mode.The menu mode window will be
displayed.
2 Press v or V on the control button toselect Detail Menu, and then press N/
ENT.
3 Press v or V on the control button toselect SYNC REC, and then press N/
ENT.
4 Press v or V on the control button toselect ON, and then press N/ENT.
5 Press x STOP to exit the menu mode.
6 Connect other equipment to the ICrecorder when the IC recorder is in the
stop mode.Connect the audio output connector
(stereo mini-plug) of other equipment to
them (microphone) jack of the ICrecorder using an audio connecting cable
(page 41)*.
Select Input appears in the displaywindow.
If Select Input is not displayed, set it in
the menu (page 82).
7 Press v or V on the control button toselect Audio IN, and then press N/
ENT.
8 Press x STOP to exit the menu mode. To record without using the
8/7/2019 manual grabadora ICDUX200
39/124
39GB
O
therRecordingOperations
8 Press x STOP to exit the menu mode.
9 Press z REC/PAUSE to start recording. flashes and the IC recorder
enters the recording pause mode.
10 Start playback on the piece ofequipment connected to the IC
recorder.
appears on the display and
synchronized recording starts.
The synchronized recording pauses when
no sound is detected for more than 2
seconds, and flashes.
The IC recorder starts recording again as a
new message when sound is detected.
P Notes During synchronized recording, you cannot
divide a message (page 34) and you cannot
pause recording (page 20).
Depending on the piece of equipment
connected to the IC recorder, thesynchronized recording function may not
operate properly due to a difference in the
audio input level.
To record without using thesynchronized recording function
1 Press MENU to enter the menu mode.
The menu mode window will be
displayed.
2 Press v or V on the control button toselect Detail Menu, and then press N/
ENT.
3Press
vor
Von the control button toselect SYNC REC, and then press N/
ENT.
4 Press v or V on the control button to 7 Press v or V on the control button to
8/7/2019 manual grabadora ICDUX200
40/124
40GB
select OFF, and then press N/ENT.
5 Press x STOP to exit the menu mode.
6 Connect other equipment to the ICrecorder when the IC recorder is in thestop mode.
Connect the audio output connector
(stereo mini-plug) of other equipment to
them (microphone) jack of the IC
recorder using an audio connecting cable(page 41)*.
Select Input appears in the display
window.
If Select Input is not displayed, set it in
the menu (page 82).
select Audio IN, and then press N/
ENT.
8 Press x STOP to exit the menu mode.
9 Press z REC/PAUSE to start recording.The built-in microphones are
automatically cut off and the sound from
the connected equipment is recorded.
10Start playback on the piece ofequipment connected to the IC
recorder.
* Optional audio connecting cables
8/7/2019 manual grabadora ICDUX200
41/124
41GB
O
therRecordingOpe
rations
p g(not supplied)
P NoteWhen recording from other equipment, the
microphone sensitivity cannot be adjusted.
To the ICrecorder
To the otherequipment
RK-G139 Stereomini-plug(withoutresistor)
Mini-plug(monaural)(withoutresistor)
RK-G136 Stereomini-plug
(withoutresistor)
Stereomini-plug
(withoutresistor)
Other Playback Operations
Changing the Playback Method
8/7/2019 manual grabadora ICDUX200
42/124
42GB
Changing the Playback Method
Convenient playbackmethodsListening with better soundquality To listen with the headphones:
Connect the supplied headphones to the
i (headphone) jack. The built-in speakerwill be automatically disconnected.
To listen from an external speaker:
Connect an active or passive speaker (not
supplied) to the i (headphone) jack.
Quickly locating the point you
wish to start playback (EasySearch)When Easy Search is set to ON
(page 76) in the menu, you can quickly
locate the point at which you wish to start
playback by pressing > or . on the
control button repeatedly during playback.You can go back approx. 3 seconds by
pressing . on the control button once, or
advance approx. 10 seconds by pressing
> on the control button once. This
function is useful for locating a desired
point in a long recording.
Searching forward/backward
during playback (Cue/Review) To search forward (Cue):
Press and hold > on the control button
during playback and release it at the point
you wish to resume playback.
To search backward (Review):
Press and hold . on the control buttonduring playback and release it at the point
you wish to resume playback.
The IC recorder searches at slow speed with
playback sound. This is useful to check one
word forward or back. Then, if you pressand hold the button, the IC recorder starts to
search at higher speed.
z When messages are played backto the end of the last message
When you play back or fast play back to the
end of the last message, MESSAGE ENDlights up for approx. 5 seconds.
When MESSAGE END and the operation
indicator go off, the IC recorder will stop at
the beginning of the last message.
If you press and hold . on the controlbutton while MESSAGE END is lit, the
messages are played back rapidly, and
8/7/2019 manual grabadora ICDUX200
43/124
1 Slide the DPC (SPEED CTRL) switch to during playback (page 43), or when theifi d A B ti i l d b k
8/7/2019 manual grabadora ICDUX200
44/124
44GB
ON.
2 If you wish to increase the playback
speed, press v on the control buttonwhen the IC recorder is in the playback
mode.
Every time the button is pressed, you can
increase the speed by 5% for + from
50% to 0%, and 10% for + between 0%
and 100%.
3 If you wish to decrease the playbackspeed, press V on the control button
when the IC recorder is in the playback
mode.
Every time the button is pressed, you candecrease the speed by 5% for from 0%
to 50%, and 10% for between 100%
and 0%.
To resume normal playbackSlide the DPC (SPEED CTRL) switch to
OFF.
P Notes You can only adjust the playback speed
between 0% and 50% when messages are
recorded as WMA/AAC-LC files.
When any one message is played back
repeatedly by pressing and holding N/ENT
specified A-B section is played back
repeatedly (page 46), you cannot adjust theplayback speed.
Changing the Playback Settings
8/7/2019 manual grabadora ICDUX200
45/124
45GB
OtherPlayback
Operations
g g y g
Selecting the playbackmode
You can select the playback mode in the
menu.
1 Press MENU to enter the menu modewhen the IC recorder is in the stop or
playback mode.
The menu mode window will be
displayed.
2 Press v or V on the control button to
select Play Mode, and then press N/ENT.
3 Press v or V on the control button toselect 1, , ALL, 1,
, or ALL, and then press
N/ENT.
4 Press x STOP to exit the menu mode.
N/ENT
MENU
v, V
x STOP
To stop A-B Repeat playback:
P x STOP1 A message is played back.
8/7/2019 manual grabadora ICDUX200
46/124
46GB
Playing back a specified sectionrepeatedly A-B Repeat
1 During playback, press (repeat) A-Bto specify the starting point A.
A-B B? is displayed.
2 Press (repeat) A-B again to specify
the finishing point B. A-B is displayed and the specified
section is played back repeatedly.
To resume normal playback:
Press N/ENT.
Press x STOP.
To change the segment specified for A-B
Repeat playback:During A-B Repeat playback, press
(repeat) A-B again to specify a new
starting point A. Then specify a new
finishing point B, as in step 2.
P NoteYou cannot specify the finishing point B
before the starting point A that has been set.
Messages in one folder are playedback continuously.
ALL All the messages are played backcontinuously.
1 One message is played backrepeatedly.
Messages in one folder are played
back repeatedly.
ALL All the messages are played backrepeatedly.
Making the human voiceclearer the noise c t
The menu mode window will be
displayed
8/7/2019 manual grabadora ICDUX200
47/124
47GB
OtherPlayback
Operations
clearer the noise cutfunction
When the noise cut function is set to ON
in the menu, the distortion of very low and
high frequencies which are outside the
human voice range is reduced, therefore
you can hear the human voice more clearly.
1 Press MENU to enter the menu modewhen the IC recorder is in the stop or
playback mode.
displayed.
2 Press v or V on the control button to
select Noise Cut, and then press N/ENT.
3 Press v or V on the control button toselect ON, and then press N/ENT.
4 Press x STOP to exit the menu mode.
P Notes
The effect of the noise cut function may bedifferent depending on the condition of the
recorded voice.
When you are using the built-in speaker or
listening to the FM radio, the noise cut
function does not work.
To cancel the noise cut functionSet Noise Cut to OFF in step 3.
N/ENT
MENU
v, V
xSTOP
Selecting the sound effect 2 Press v or V on the control button toselect Effect and then press N/ENT
8/7/2019 manual grabadora ICDUX200
48/124
48GB
You can set the effect you want for the
playback in the menu.
1 Press MENU to enter the menu modewhen the IC recorder is in the stop or
playback mode.
The menu mode window will be
displayed.
select Effect, and then press N/ENT.
3 Press v or V on the control button toselect effect you want for the playback,
and then press N/ENT.
4 If you select Custom, you can press vor V on the control button to adjust the
sound level for each band.
Press . or > on the control button
to move to the band on the left or right.
5 Press N/ENT to close the customsetting window.
6 Press x STOP to exit the menu mode.
N/ENT
MENU
v, V
., >
x STOP
Pop Stresses middle ranges, ideal forvocals
8/7/2019 manual grabadora ICDUX200
49/124
49GB
OtherPlayback
Operations
P Notes When you are using the built-in speaker orlistening to the FM radio, this setting is
invalid.
When the noise cut function is set to ON in
the menu, this setting is invalid.
vocals.
Rock Emphasizes high and low ranges for
a powerful sound.
Jazz Emphasizes high ranges for livelysound.
Bass1 Emphasizes the bass sound.
Bass2 Emphasizes the bass sound even
more.
Custom You can design your own customsound level for 5 bands of EQ.
OFF The Effect function does not work.
Playing Back a Message at a Desired Timeith Al
8/7/2019 manual grabadora ICDUX200
50/124
50GB
with an Alarm
You can sound an alarm and start playback
of a selected message at a desired time.
You can have the message played back on aspecified date, once every week, or at the
same time every day.
You can set a maximum of 30 alarms.
1 Select the message you want to play backwith an alarm.
2 Enter the alarm setting mode.
1 Press MENU to enter the menu mode
when the IC recorder is in the stop
mode.The menu mode window will be
displayed.
2 Press v or V on the control button toselect Alarm, and then press N/
ENT.
3 Press v or V on the control button to
select New, and then press N/
ENT.
N/ENT
MENU
v, V
x STOP
3 Set the alarm date and time.
1 Press v or V on the control button to
2 Press v or V on the control button toselect the item you want to change, then
8/7/2019 manual grabadora ICDUX200
51/124
51GB
OtherPlayback
Operations
1 Press v or V on the control button toselect Date, a day of the week, or
Daily, and then press N/ENT.
2When you select Date:
Set the year, month, day, hour, and
minute in sequence, as described inStep 4: Setting the Clock on
page 13.
Executing..., then your settings aredisplayed.When you select a day of the week
or Daily:
Press v or V on the control button to
set the hour, and then press N/ENT,press v or V on the control button to
set the minute, and then press N/
ENT.
4 Press x STOP to exit the menu mode.The setting process is finished and ,(alarm indicator) appears in the display
window.
To change the alarm setting1 Select Alarm - List in the menu, then
press N/ENT.
The alarm list is displayed.
y g ,
press N/ENT.
3 Press v or V on the control button toselect Edit, then press N/ENT.
4 Select Date, a day of the week, orDaily, then press N/ENT.
5 Set the date and time and press N/ENT.Executing..., then your settings are
displayed.
6 Press x STOP to exit the menu mode.
To cancel the alarm setting
Follow steps 1 and 2 of To change thealarm setting. In step 3, select Cancel
and press N/ENT. Cancel Alarm? is
displayed. Press v or V on the control
button to select Execute, then press N/
ENT. The alarm will be cancelled and the
alarm indicator will disappear from thedisplay window.
To set the alarm pattern
1 Select Alarm - Pattern in the menu,then press N/ENT.
2 Press v or V on the control button toselect Beep&Play, Beep or Play,
When the clock has not been set or no
messages are recorded, you cannot set the
8/7/2019 manual grabadora ICDUX200
52/124
52GB
p y p y
then press N/ENT.
3 Press x STOP to exit the menu mode.
When the set date and timecomesAt the set time, Alarm is displayed in the
display window and the alarm and the
selected message will be played back using
the selected alarm pattern.
When the playback ends, the IC recorder
will stop automatically. (When the alarm
pattern is set to Beep&Play or Play, the
IC recorder will stop at the beginning of the
selected message.)
To listen to the same messageagainPress N/ENT, and the same message will
be played back from the beginning.
To stop the alarm playbackPress any button other than VOL +/ while
the alarm sound is heard. If the HOLD
function is activated, you can stop the alarm
playback by pressing any button.
P Notes
You can set only one alarm each onemessage.
alarm.
The alarm sounds even if you set Beep to
OFF in the menu (page 80). If the alarm time comes during recording,the alarm will sound after the recording is
finished. , will flash when the alarm timecomes.
If the alarm time comes while you are
updating data, the alarm will be cancelled
automatically. If more than one alarm time comes, only the
first message will be played back with an
alarm.
Once the alarm is set, the alarm will not be
cancelled, even after the message is played
back.
If the alarm time comes while anothermessage is being played back with an alarm,
the payback stops and the new message will
be played back.
If you divide a message you have set an
alarm for, the alarm setting remains on only
the first part of the divided message.
If you delete a message on which you haveset an alarm, that alarm will be also
cancelled.
Playback via Other Devices
8/7/2019 manual grabadora ICDUX200
53/124
53GB
OtherPlayback
Operations
Recording with other
equipment
You can record the sound of the IC recorder
with other equipment.
Before you start recording, we recommend
you to make trial recording first.
1 Connect the i (headphone) jack of the
IC recorder to the audio input connector
(stereo minijack) of other equipment
using an audio connecting cable*.
2 Press N/ENT to start playback and atthe same time set the connected
equipment to the recording mode.
A message from the IC recorder will be
recorded on the piece of equipmentconnected.
3 Press x STOP on the IC recorder and theconnected equipment at the same time to
stop recording.
* Optional audio connecting cables(not supplied)
Tape recorder, etc.
x STOP
N/ENT
i (headphone) jack
To the ICrecorder
To the otherequipment
RK-G139 Stereomini-plug
(withoutresistor)
Mini-plug(monaural)
(withoutresistor)
RK-G136 Stereomini-plug(withoutresistor)
Stereomini-plug(withoutresistor)
P NoteYour dealer may not handle some of the above
8/7/2019 manual grabadora ICDUX200
54/124
54GB
listed optional accessories. Please ask the
dealer for detailed information.
Editing Messages
Erasing All Messages in a Folder
8/7/2019 manual grabadora ICDUX200
55/124
55GB
E
ditingMessages
P NoteIf the selected folder contains a protected
message, you cannot erase the message.
1 Select the folder containing the messages
you want to erase when the IC recorder isin the stop mode.
2 Press MENU to enter the menu mode.The menu mode window will be
displayed.
3 Press v or V on the control button to
select Erase All, and then press N/ENT.
4 Press v or V on the control button toselect Execute, and then press N/
ENT.
Erasing... appears in the display
window and all messages in the selected
folder will be erased.
5 Press x STOP to exit the menu mode.
To cancel erasingSelect Cancel in step 4, and then press
N/ENT.
N/ENT
MENU
v, V
Moving a Message to a Different Folder
8/7/2019 manual grabadora ICDUX200
56/124
56GB
P Notes When is displayed for the folder
indicator, you cannot move a message
(page 85).
You cannot move a message to a folder.
1 Select the message you want to move.
2 Press MENU to enter the menu modewhen the IC recorder is in the stop or
playback mode.
The menu mode window will be
displayed.
3 Press v or V on the control button toselect Move, and then press N/ENT.
The message to be moved will be played
back.
4 Press v or V on the control button toselect the folder that you want to move
the message into, and then press N/
ENT.
Executing... is displayed and the
message is moved to the last position in
the destination folder.
N/ENT
MENU
v, V
x STOP
8/7/2019 manual grabadora ICDUX200
57/124
Dividing a Message into Two
8/7/2019 manual grabadora ICDUX200
58/124
58GB
You can divide a message during playback,
so that the message is divided into two parts
and a new message number is added to the
newer part of the divided message. By
dividing a message, you can easily find thepoint from which you want to play back
when you make a long recording such as at
a meeting. You can divide a message until
the total number of messages in the folder
reaches the maximum number allowed.
1 Press DIVIDE while you are playing
back the message you want to divide.Divide? appears with the message title.
2 Press v or V on the control button toselect Execute, and then press N/
ENT.
Dividing... appears, a new number isadded to the newer part of the divided
message, and the message numbers of
the following messages will be
incremented by one.
N/ENT
DIVIDE
v, V
., >
Message 1 Message 2 Message 3
v
fA Message is divided.
Message 1 Message 2 Message 3 Message 4
The message numbers are incremented.
P Notes You need a certain amount of free space in
the memory to divide a message
8/7/2019 manual grabadora ICDUX200
59/124
59GB
EditingMessages
the memory to divide a message.
When you divide a message with a title and
artist name, the newer part has the same title,artist name, and file name.
You cannot divide a message other than theone recorded using the IC recorder (MP3/
WMA/AAC-LC file transferred from a
computer).
Once a message is divided, you cannot
combine divided messages using the ICrecorder.
If you divide a message with an alarmsetting, the same alarm setting remains only
with the former message divided.
You may not be able to divide a message atthe beginning or at the end of the message
because of system limitations.
To play the divided messagePress . or > on the control button to
display the message number, as the divided
messages now each have message numbers.
Listening to the FM Radio
Tuning in an FM Radio Station
8/7/2019 manual grabadora ICDUX200
60/124
60GB
(for ICD-UX200F/UX300F only)
The headphone cord is an FM antenna,
therefore, connect the headphone when
listening to the radio.
P NoteDuring FM reception you cannot charge the
battery.
1 Press MENU to enter the menu mode.
The menu mode window will bedisplayed.
2 Press v or V on the control button toselect FM Radio, and then press N/
ENT.
The IC recorder enters the FM radiomode.
3 Press v or V on the control button toselect frequency.
N/ENT
MENU
v,
V
., >
4 Press . or > on the control buttonrepeatedly to tune in a station or press
and hold . or > on the control
Switching the FM radiooutput between speaker andheadphones
8/7/2019 manual grabadora ICDUX200
61/124
61GB
Liste
ningtotheFMRadio
and hold . or > on the control
button until the frequency digits begin to
change on the display.The IC recorder automatically scans the
radio frequencies and stops when it finds
a clear station.
If you cannot tune in a station, press .
or > on the control button repeatedly
to change the frequency step by step.
Display when listening to the FMradio
headphones
During FM reception or FM recording, you
can switch between the sound from the
speaker and the sound from the headphones
using the menu.
1 During FM reception or FM recording,press MENU to enter the menu mode
when listening to the FM radio.
The menu mode window will be
displayed.
FM indication
Radio frequency
Preset number
Receiver sensitivity
N/ENT
MENU
v, V
x STOP
2 Press v or V on the control button toselect Audio Output, and then press
N/ENT.
Switching the receiversensitivity of the FM radio
8/7/2019 manual grabadora ICDUX200
62/124
62GB
3 Press v or V on the control button to
select Headphones or Speaker, andthen press N/ENT.
The FM radio output is set to
Headphones when you purchase the IC
recorder.
4 Press x STOP to exit the menu mode.
You can set the receiver sensitivity when
listening to the FM radio.
1 Press MENU to enter the menu mode
when listening to the FM radio.The menu mode window will be
displayed.
N/ENT
MENU
v, V
x STOP
2 Press v or V on the control button toselect DX/LOCAL, and then press N/
ENT.
Recording FM broadcasts
8/7/2019 manual grabadora ICDUX200
63/124
63GB
ListeningtotheFMRadio
3 Press v or V on the control button to
select DX or LOCAL, and then pressN/ENT.
4 Press x STOP to exit the menu mode.
P NoteSelect DX when the IC recorder reception
status is not good due to a weak signal.
1 Tune in the station you want to record.
2 Press z REC/PAUSE to start recording.
3 Press x STOP to stop recording.DX Normally, select this setting.
LOCAL When there is interference or
collapsing caused by a intenseelectric field around the transmittingantenna of the broadcasting station,etc., select this setting.
z REC/PAUSE
x STOP
Presetting FM Radio Stations Automatically
2
8/7/2019 manual grabadora ICDUX200
64/124
64GB
You can preset up to 30 FM radio stations
automatically using the preset menu.
1 Press MENU to enter the menu mode
when listening to the FM radio.The menu mode window will be
displayed.
2 Press v or V on the control button to
select Auto Preset, and then press N/ENT.
3 Press v or V on the control button toselect Execute, and then press N/
ENT.
The IC recorder automatically scans for
available radio frequencies and the
stations will be stored in memory from
the lower frequencies to the higher ones.
While presetting FM radio stations
automatically, the preset number ready to
be assigned flashes.
N/ENT
MENU
v, V
x STOP
To stop the automatic presettingPress x STOP. The preset numbers stored
until you press the x STOP button remain
Switching the scanningsensitivity
8/7/2019 manual grabadora ICDUX200
65/124
65GB
ListeningtotheFMRadio
y p
in memory.
You can set the scanning sensitivity when
presetting FM radio stations.
1 Press MENU to enter the menu mode
when listening to the FM radio.The menu mode window will be
displayed.
N/ENT
MENU
v, V
x STOP
2 Press v or V on the control button toselect Scan Sensitivity, and then press
N/ENT.
8/7/2019 manual grabadora ICDUX200
66/124
66GB
3 Press v or V on the control button toselect High(SCAN H) or
Low(SCAN L), and then press N/
ENT.
The scanning sensitivity is set to
High(SCAN H) when you purchase
the IC recorder.
4 Press x STOP to exit the menu mode.
Presetting FM Radio Stations Manually
2 P N/ENT
8/7/2019 manual grabadora ICDUX200
67/124
67GB
ListeningtotheFMRadio
You can preset up to 30 FM radio stations
in the IC recorders memory.
1 Tune in the station you want to presetand store on the preset number.
When the station you want to tune in is
not a preset station, P - - is displayed.
In this case, you can register it with the
new preset number.
2 Press N/ENT.
The preset number, frequency and Set?will be displayed on the display.
3 Press v or V on the control button toselect Execute, and then press N/
ENT.
The station will be stored in memory.N/ENT
v, V
Listening to a Preset Radio Station
The IC recorder enters the FM radio
8/7/2019 manual grabadora ICDUX200
68/124
68GB
1 Press MENU to enter the menu modewhen the IC recorder is stopped.
The menu mode window will be
displayed.
2 Press v or V on the control button toselect FM Radio, and then press N/
ENT.
The IC recorder enters the FM radio
mode.
3Press
vor
Von the control button toselect preset number.
4 Press . or > on the control buttonrepeatedly until the preset number you
want is displayed.
When you press and hold . or > on
the control button, the preset numbers
change rapidly.
5 Press x STOP to turn the FM radio off.
N/ENT
MENU
v, V
x STOP
., >
Erasing Preset FM Radio Stations
The IC recorder enters the FM radio mode
8/7/2019 manual grabadora ICDUX200
69/124
69GB
ListeningtotheFMRadio
The display in the display window may be
different from the actual one in some
regions.
1 Press MENU to enter the menu mode.The menu mode window will bedisplayed.
2 Press v or V on the control button toselect FM Radio, and then press N/
ENT.
The IC recorder enters the FM radio mode.
3 To tune in a station, press . or >on the control button repeatedly until the
preset number you want to erase is
displayed.
4 Press N/ENT.The preset number, frequency and
Erase? will be displayed on the
display.
5 Press v or V on the control buttonrepeatedly to select Execute, and then
press N/ENT.
N/ENT
MENU
v, V
., >
The preset number will be changed to
P - -.
8/7/2019 manual grabadora ICDUX200
70/124
70GB
About the Menu Function
Making Settings for the Menu
8/7/2019 manual grabadora ICDUX200
71/124
71GB
AbouttheMenuFun
ction
1 Press MENU to enter the menu mode.The menu mode window will be
displayed.
2 Press v or V on the control button toselect the menu item for which you want
to make setting, and then press N/ENT.
3 Press v or V on the control button toselect the setting that you want to set,
and then press N/ENT.
4 Press x STOP to exit the menu mode.
P NoteIf you do not press any button for 1 minute, the
menu mode is automatically cancelled and the
window will return to the normal display.
To return to the previous windowPress . on the control button during
menu mode.
To exit the menu modePress x STOP or MENU.
N/ENT
MENU
v, V
x STOP
., >
Menu Settings
Menu items Settings Operation mode
8/7/2019 manual grabadora ICDUX200
72/124
72GB
Menu items Settings Operation mode
(a
: the setting can be made/ : the setting cannot be made)
Stop
mode
Playback
mode
Recording
mode
FM radio
mode
FM radio
recording
mode
REC Mode ST, STSP, STLP, SP, LP a a
Mic Sensitivity S-High , High , Low a a
LCF(Low Cut) ON, OFF a a
VOR ON, OFF a a
Noise Cut ON, OFF a a
Effect Pop, Rock, Jazz, Bass1, Bass2,
Custom, OFF
a a
Easy Search ON, OFF a a
Play Mode 1, , ALL, 1, ,
ALL
a a
Display Elapsed Time, Remain Time,REC Date, REC Time
a a a a
Alarm New, List, Pattern a
Protect Execute, Cancel a
Move (Folder to be moved) a a
Erase All Execute, Cancel a
FM Radio* a
Auto Preset* Execute, Cancel a
DX/LOCAL* DX, LOCAL a a
* for ICD-UX200F/UX300F only
Menu items Settings Operation mode
(a : the setting can be made/
: the setting cannot be made)
Stop Playback Recording FM radio FM radio
8/7/2019 manual grabadora ICDUX200
73/124
73GB
AbouttheMenuFun
ction
Scan Sensitivity* High(SCAN H), Low(SCAN L) a
Audio Output* Headphones, Speaker a a
Detail Menu a
Date&Time _ _ y _ _ m _ _ d _ _ : _ _ a
Time Display 12-Hour, 24-Hour a
Beep ON, OFF a
LED ON, OFF a
Backlight ON, OFF a
Language English, Espaol (Spanish),Franais (French)
a
USB Charge ON, OFFa
Auto Power Off 5min, 10min, 30min, 60min a
Select Input MIC IN, Audio IN a
SYNC REC ON, OFF a
Format Execute, Cancel a
p
mode
y
mode
g
mode mode recording
mode
* for ICD-UX200F/UX300F only
Menu items Settings (*: Initial setting) See page
REC Mode Sets the recording mode.ST*:
Stereo high-quality recording mode
28
8/7/2019 manual grabadora ICDUX200
74/124
74GB
Stereo high quality recording mode
STSP:Stereo standard recording modeSTLP:
Stereo long play recording modeSP:
Monaural standard play recording modeLP:
Monaural long play recording mode
Mic Sensitivity Sets the microphone sensitivity.
S-High :To record a sound far away from the IC recorder or a lowsound, such as a recording made in a spacious room.
High *:To record the sound of a normal conversation or meeting, suchas a recording made in a conference room or duringinterviews.
Low :To record dictation with a microphone in front of your mouth,a sound near the IC recorder, or a loud sound.
29
LCF(Low Cut) Sets the LCF (Low Cut Filter) function to cut a low frequency toreduce the roaring noise from wind; therefore you can record a
message more clearly.ON:The LCF function is activated.
OFF*:The LCF function is cancelled.
31
VOR Sets the VOR (Voice Operated Recording) function.ON:
Recording starts when the IC recorder detects sound and
32
Menu items Settings (*: Initial setting) See page
8/7/2019 manual grabadora ICDUX200
75/124
75GB
AbouttheMenuFun
ction
g
pauses when no sound is heard, eliminating recording duringsoundless periods. The VOR function is activated whenz REC/PAUSE is pressed.
OFF*:The VOR function does not work.
Noise Cut Sets the noise cut function.
ON:
The distortion of very low and high frequencies which areoutside the human voice range is reduced, therefore you canhear the human voice more clearly.
OFF*:
The noise cut function does not work.
47
Effect Sets the effect you want for the playback in the menu.Pop:
Stresses middle ranges, ideal for vocals.
48
Menu items Settings (*: Initial setting) See page
8/7/2019 manual grabadora ICDUX200
76/124
76GB
g
Rock:Emphasizes high and low ranges for a powerful sound.Jazz:
Emphasizes high ranges for a lively sound.Bass1:
The bass sound is emphasized.Bass2:
The bass sound is emphasized even more.
Custom:You can design your own custom sound level for 5 bands ofEQ.
OFF*:The Effect function does not work.
P NoteWhen playing back messages using the built-in speaker, listening
to the FM radio, or when the noise cut function is set to ON inthe menu, the Effect function does not work.
Easy Search Sets the easy search function.ON:
You can go forward for about 10 seconds by pressing > onthe control button and go back for about 3 seconds by pressing. on the control button. This function is useful when
attempting to locate desired point in a long recording.OFF*:
The easy search function does not work. When you press .or > on the control button, a message will be movedforward or backward.
42
Play Mode Sets the playback mode.1:
A message is played back.
45
Menu items Settings (*: Initial setting) See page
8/7/2019 manual grabadora ICDUX200
77/124
77GB
AbouttheMenuFun
ction
*:Messages in one folder are played back continuously.ALL:
All the messages are played back continuously.1:
One message is played back repeatedly.:
Messages in one folder are played back repeatedly.
ALL:All the messages are played back repeatedly.
Display Changes the display mode.Elapsed Time*:
Elapsed playback time of one messageRemain Time:
During stop or playback, the remaining time of the message
During recording, the available recording timeREC Date:Date recorded
REC Time:Time recorded
Alarm Sets the alarm.New*:
To set the alarm, select New and set the date, time or day of
50
Menu items Settings (*: Initial setting) See page
8/7/2019 manual grabadora ICDUX200
78/124
78GB
the week or choose daily for playback.List:A list of dates or the days of the week, and times at which thealarm has already been set will be displayed.Edit: You can change the selected date or day of the week andtime.Cancel: You can cancel the alarm setting on the selected dateor on a day of the week.
Pattern:Sets the alarm sound pattern for all alarm settings.Beep&Play*: The selected message is played back after thealarm sounds.Beep: Only the alarm sounds.Play: Only the selected message is played back.
Protect Protect the selected message to prevent the message from being
erased, divided, or being moved.Execute:Protect the selected message. If you specify a message that hasalready been protected, cancel the protection.
Cancel*:Set Protection? or Erase Protection? is not executed.
Move The selected message will be moved to the selected folder.Before attempting to move a message, select the message to bemoved, and then go to the menu window.
56
Erase All All messages in the selected folder will be erased.Press to return to the folder window before erasing themessages and select a folder from which all messages are to beerased, and then go to the menu window and select Execute.
55
FM Radio** The IC recorder enters the FM radio mode. 60
Auto Preset** Scans automatically for available frequencies. The stations willbe stored in memory.
64
Menu items Settings (*: Initial setting) See page
8/7/2019 manual grabadora ICDUX200
79/124
79GB
AbouttheMenuFun
ction
be stored in memory.
Execute:The automatic presetting is activated.
Cancel*:The automatic presetting is cancelled.
DX/LOCAL** Sets the receiver sensitivity when listening to the FM radio.DX*:
Normally, select this setting.
LOCAL:When there is interference or collapsing caused by a intenseelectric field around the transmitting antenna of thebroadcasting station, etc., select this setting.
P NoteSelect DX when the IC recorder reception status is not good
due to a weak signal.
62
Scan Sensitivity** Sets the scanning sensitivity when presetting FM radio stations.High(SCAN H)*:
The scanning sensitivity is set to high.Low(SCAN L):
The scanning sensitivity is set to low.
65
Audio Output** During FM reception or FM recording, you can switch between
the sound from the speaker and the sound from the headphones.Headphones*:The sound comes out from the headphones.
Speaker:The sound comes out from the speaker(s).
61
** for ICD-UX200F/UX300F only
Detail Menu
Date&Time Sets the clock by setting year, month, day, hour, and minute insequence.
13
Menu items Settings (*: Initial setting) See page
8/7/2019 manual grabadora ICDUX200
80/124
80GB
q
Time Display Sets the clock display.12-Hour*:
12:00AM = midnight, 12:00PM = noon24-Hour:
0:00 = midnight, 12:00 = noon
Beep Sets whether a beep will be heard or not.ON*:
A beep will sound to indicate that an operation has beenaccepted or an error has occurred.
OFF:No beep sound will be heard.
P NoteThe alarm sounds even if you set Beep to OFF in the menu.
LED Turns the operation indicator on or off during operation.ON*:
During recording or playback, the operation indicator lights orflashes.
OFF:The operation indicator does not light or flash, even duringoperation.
P NoteWhen the IC recorder is connected to a computer, the operation
indicator lights or flashes even if LED is set to OFF.
Backlight Turns the backlight in the display window on or off.ON*:
The backlight in the display window lights up for approx. 10seconds
Menu items Settings (*: Initial setting) See page
8/7/2019 manual grabadora ICDUX200
81/124
81GB
AbouttheMenuFun
ction
seconds.OFF:
The backlight in the display window does not light, evenduring operation.
Language Sets the language to be used for messages, menus, folder names,file names, etc.English, Espaol (Spanish), Franais (French)
15
USB Charge Sets whether battery will be charged using a USB connection ornot.ON*:
The battery will be charged.OFF:
The battery will not be charged.
P Note
If you use a USB AC adaptor (not supplied) to connect the ICrecorder to the AC outlet, you can charge battery regardless this
setting.
9
Auto Power Off If the IC recorder is on and left for the period you have set, the ICrecorder turns off automatically.5min:
The IC recorder will be turned off after approx. 5 minutes.
10min*:The IC recorder will be turned off after approx. 10 minutes.
30min:The IC recorder will be turned off after approx. 30 minutes.
60min:The IC recorder will be turned off after approx. 60 minutes.
Select Input Selects the external input to be recorded that is connected to them (microphone) jack.MIC IN*:
Select when you record messages using an external
36, 37
Menu items Settings (*: Initial setting) See page
8/7/2019 manual grabadora ICDUX200
82/124
82GB
Select when you record messages using an externalmicrophone.
Audio IN:Select when you record using other equipment.
SYNC REC When set to ON, the IC recorder enters the recording pausemode when no sound is detected for more than 2 seconds, and theIC recorder starts recording again as a new message when anysound is detected.
ON:The synchronized recording function is activated.
OFF*:The synchronized recording function is cancelled.
37
Format Sets the formatting of the drive.Execute:
Formatting... appears and the drive will be formatted.
Cancel*:The drive will not be formatted.
P Notes Use the IC recorder formatting function to format the memory.
When the memory is formatted, all the data stored in the IC
recorder will be erased. Once the memory has been erased, you
cannot retrieve the data that was erased.
Utilizing Your Computer
Using the IC Recorder with Your Computer
When the IC recorder is connected to your
computer, the IC recorder is recognized bySystem requirements for
8/7/2019 manual grabadora ICDUX200
83/124
83GB
UtilizingYourComputer
p , g y
the computer, and you can transfer data
between them.
Copying messages from the ICrecorder to your computer tosave them (page 87)
You can copy the messages recorded on theIC recorder to save them.
Copying music files from yourcomputer to the IC recorder toplay them back (page 88)You can copy MP3/WMA/AAC-LC files
saved on your computer by a simple drag &
drop operation when you connect the
IC recorder to your computer. You can also
play back the copied files.
Using the IC recorder as USB
memory data storage function(page 91)You can store image data or text data saved
on the computer temporarily in the IC
recorder.
your computerSee System requirements on page 99.
Connecting the IC recorderto your computer
The IC recorder is recognized by the
computer as soon as the connection is
made. While the IC recorder is connected to
the computer, Connecting is displayed in
8/7/2019 manual grabadora ICDUX200
84/124
84GB
1 Slide the USB lever on the back of the ICrecorder in the direction of the arrow,
and insert the USB connector into the
USB port of a running computer.
2 Make sure the IC recorder has beenrecognized properly.
On the Windows screen; open My
Computer or Computer, and make
sure that IC RECORDER has been
recognized.
On the Macintosh screen; make sure that
an IC RECORDER drive is displayed
on the desktop.
the display window of the IC recorder.
If you cannot insert the USB connector of
the IC recorder into the USB port of a
computer directly, use the supplied USB
connection support cable.
P Notes If you connect more than two USB devices
to your computer, normal operation will notbe guaranteed.
Use of this IC recorder with a USB hub or a
USB connection support cable other than the
supplied cable is not guaranteed.
A malfunction may occur depending on the
USB devices connected at the same time.
To USB port
IC recorder
Computer
USB connection supportcable (supplied)
Before connecting the IC recorder to the
computer, make sure that the battery is
inserted in the IC recorder.
It is recommended that you disconnect the
IC recorder from the computer when you are
Construction of folders andfiles
If you connect the IC recorder to your
computer, you can see the structure of
8/7/2019 manual grabadora ICDUX200
85/124
85GB
UtilizingYourComputer
not using the IC recorder connected to thecomputer.
folders and files on the computer screen.
IC RECORDER
Folder for messagesrecorded using the ICrecorder
Folder transferred fromyour computer
VOICE
FOLDER01
FOLDER10
Conversation*
1
MUSIC
POP
OLDIES*1
*3
*2
The folders and files are displayed on the
computer screen as shown.
The folder indicators in the display window
of the IC recorder are as follows:
z Tips You can change the folder name, title, artist
name, and/or file name using a computer.
The title or artist name, etc., registered in themusic files, can be displayed on the IC
8/7/2019 manual grabadora ICDUX200
86/124
86GB
P NoteYou can record messages in up to 10 folders
(FOLDER01-10) using the IC recorder.
*1 The name of a folder in which music files
are stored will be displayed on the IC
recorder as it is, so it is convenient if you
put an easy-to-remember name on the
folder in advance.
Folders shown in the illustration are
examples of folder names.*2 The IC recorder can recognize up to 8 levels
of folders copied to the IC recorder.
*3 If you copy music files separately, they are
classified as being in No Folder.
recorder. It is useful if you input the ID3 taginformation using the software you use to
make the music files on your computer.
You can display the information in sequence
by pressing v or V on the control button
(page 89).
P Notes You cannot copy 511 or more folders(except VOICE folders) or files to the root
directory that is located immediately below
IC RECORDER on the computer. This isdue to system limitations (for ICD-UX200/
UX200F only).
If no title, or artist name has been registeredUnknown will be displayed.
: Folder for messages recorded usingthe IC recorder (They have been
already made when you purchase
the IC recorder.)
: Folder transferred from a computer
(They are displayed when music
files have been transferred from acomputer.)
Copying Messages from the IC Recorder toYour Computer to Save Them
z
8/7/2019 manual grabadora ICDUX200
87/124
87GB
UtilizingYourC
omputer
You can save messages or folders bycopying them from the IC recorder to your
computer.
1 Connect the IC recorder to yourcomputer (page 84).
2 Copy messages or folders you want tosave to your computer.
Drag and drop the messages or folders
you want from IC RECORDER to the
local disc on your computer.
z To copy a message or a folder(Drag and drop)
3Disconnect the IC recorder from yourcomputer (page 94).
If you wish to create a CD, use a
commercially available CD burner software
application, a CD burner software application
installed on your computer, or WindowsMedia Player.
For details about operations for the CD burner
software application or Windows Media
Player, refer to the operating instructions
supplied with the software application, or
contact the respective manufacturers.
1Click and hold,2 drag,3 and then drop.
Copying Music Files from Your Computer tothe IC Recorder and Playing Them Back
8/7/2019 manual grabadora ICDUX200
88/124
88GB
You can copy music or other audio files
(MP3/WMA/AAC-LC*) from your
computer to the IC recorder by dragging
and dropping them, and you can then play
them back on the IC recorder.
You can make an MP3/WMA/AAC-LC file
using a software application, etc., installed
on your computer.
* For the file formats that can be played backusing the IC recorder, see Specifications
(page 99).
Copying a music file fromyour computer to the ICrecorder (drag and drop)
1 Connect the IC recorder to yourcomputer (page 84).
2 Copy the folder in which the music filesare stored to the IC recorder.
On the Windows screen using Explorer,
and on the Macintosh screen using
Finder, drag and drop the folder onto the
IC recorder.
The IC recorder can recognize up to 500
folders. You can copy up to 999 files to
one folder and up to 5,000 files in total.
3 Disconnect the IC recorder from yourcomputer (page 94).
4 Press .
5 Press v or V on the control button toselect the folder ( ) in which music
files are stored, and then press > on
the control button.
8/7/2019 manual grabadora ICDUX200
89/124
Enjoying the music filesmore
Selecting the playback modeYou can select the playback mode, such as
l b k f i fil ti
Playing back a message at adesired time with an alarmYou can start playback of a selected
message at a desired time.
For details see page 50
8/7/2019 manual grabadora ICDUX200
90/124
90GB
playback of one music file, continuous
playback of music files in one folder,
continuous playback of all music files,
repeat playback of one music file, repeat
playback of music files in one folder and
repeat playback of all music files, in the
menu.
For details, see page 45.
Adjusting the playback speed the DPC (Digital Pitch Control)function
You can adjust a playback speed between+100% and 50% of normal speed in the
menu. You can only adjust the playback
speed between 0% and 50% when
messages are recorded as WMA/AAC-LC
files.
For details, see page 43.
Selecting a sound effectYou can cut the noise or set a effect such as
Pop, Rock, Jazz, Bass1, Bass2,
or Custom for the playback item in the
menu.
For details, see page 47 and 48.
For details, see page 50.
8/7/2019 manual grabadora ICDUX200
91/124
Using Voice Recognition Software
When voice recognition software (not
supplied) is installed on your computer, you
can transcribe a message into a text file
Edition (not supplied) on your computer. Toinstall Dragon NaturallySpeaking, your
computer should meet the specified system
8/7/2019 manual grabadora ICDUX200
92/124
92GB
can transcribe a mes