8/16/2019 Alarma AM375

1/2

CAR ALARM AM-375REMOTE CONTROL

Button Functions Conditions

1

a. sets alarm and lock doors

 b. car finder with sound

c. temporary stop alarm from sounding

d. lock doors

alarm is disarmed

alarm is being armed

alarm is sounding

while driving

2

a. deactivates alarm

 b. unlock doorsc. stop alarm from sounding

alarm is being armed

while drivingalarm is sounding

3

a. sets soundless alarm

 b. car finder without sound

c. anti-car-jack

alarm is disarmed

alarm is being armed

while driving

1+2 panic anytime

2+3 open trunk or window or etc. alarm is disarmed

 Note: Please refer the above table and the following operating instructions fo r all function.

Use Hopping code for transmission.

The power wire has to be connected to fuse box.

FEATURES

CODE LEARNINGa. ACC ON, press Valet Switch 10 times within 8 seconds. Siren will sound 3 times to enter

code learning. Then press any button on the remote control within 8 seconds.

 b. If a new remote con trol is to be programmed, all existing remote controls must be

reprogrammed at the same time. 3 remote controls can be programmed maximum.

ARMING a. Press button 1.

 b. Siren will sound once . If silent mode, siren will not sound.c. Parking light will flash once.

d. Door will lock at 0.5sec or 3.5 sec (See Jumper Selection J2)

e. LED will flash slowly.

f. Disables engine starter (if relay connected).

g. After 3 seconds, alarm is armed. If the alarm is triggered within 3 sec, the circuit will be by -

 pass, and then alarm will rearm i tself.

DISARMING a. Press button 2 .

 b. Siren will sound 3 tim es. If siren sounds 4 times, it means the a la rm has been activated. If

silent mode arming, the parking lights will flash but without siren sound.

c. Parking lights will flash 3 times, if lights flash 4 times, it means the alarm has been

activated..

d. Doors will unlock at 0.5sec or 3.5sec (See Jumper Selection J2)

e. Enables engine ( if kill starter relay connected ).f. If alarm is on automatic re-arming function, LED will flash quickly. After 30 seconds alarm

will automatically rearm.

SILENT ARMING a. Press button 3.

 b. Parking lights will flash one time.

SF80-AM375T8CAR FINDERa. Alarm is armed.

 b. Press button 1: siren will sound once and park ing lights will fla sh 10 times.

c. Press button 3: car finder in silent situation ( parking lights will flash 10 times but without

siren sound )

d. Press button 2 to stop it.

ANTI CAR -HIJACKING(SEE JUMPER SELECTION J4) a. When key is in and ACC is in the ON position and the doors are closed, press the button 3

over 2 seconds, and open the door within 8 seconds, to activate anti car-hijacking mode.

 b. After enter in anti car -hijacking mode, close the door again and then 30 seconds countdown

starts.

c. After 30 seconds, siren will sound for every 2 sec, after 20 seconds then sounds continuously.

Also, parking lights will continuously flash and engine will stop (if kill starter relay

connected). Siren will stop to sound & parking lights will stop to flash when key is turned to

ACC OFF. After ACC OFF, Engine disables to start again (if kill starter relay connected).

d. Disarm the anti car-hijacking: Press button 3 for two seconds in ACC ON mode. The

 parking lights will flash 1 time .

SHOCK SENSOR  a. If car is lightly touched once, siren will sound for 1 second. If car is touched again within 8

seconds, siren will sound and parking lights flash for 30 seconds.

 b. If car receives a heavy shock, siren will sound for 30 seconds and parking l ights will flashfor 30 seconds.

OPEN TRUNK OR WINDOW ETC.In disarm mode: press buttons 2+3 to open trunk or window etc (module needed).

DOOR LOCK CONTROL a. Driving: press button 1 to lock doors. The doors can be locked after 0.5 or 3.5 sec (See

Jumper Selection J2) .

 b. Press button 2 to unlock doors. The doors can be unlocked afte r 0.5 or 3.5 sec(See Jump er

Selection J1).

AUTOMATIC R EARMING(SEE JUMPER SELECTION J3) When alarm is disarmed, If ACC is not switched ON position / doors not open, after 30sec

it will be automatically rearmed.

MEMORY FUNCTION The alarm will memory the condition before the power is cut off.

CURRENT SENSOR (SEE JUMPER SELECTION J1) Alarm will be activated by voltage drop such as dome light, courtesy lights or ignition lights

are turned on.

OTHER TRIGGER SENSOR  Other trigger sensor source can be added.

SENSOR BYPASS WARNING WHILE ARMING After 3 seconds, alarm is armed. If alarm is triggered by any of sensors within 3 sec, the

circuit will be by-pass, and siren will chirps 2 times for warning purpose. If the sensor is

 back to normal and keeps stable fo r 2 sec, the sensor could trigger alarm after then.

EXTERNAL PAGER OPTION The system allow pager installed for notifying driver for real time monitoring.  

FUNCTION SELECTIONThere are five jumper selection ( J1~J5). See the table as below.

Important: All jumper selections has to be determined before install. Otherwise, you haveto power off the module again for reset.

JUMPER MODE FUNCTION MODE FUNCTION 

J1: CURRENT SENSOR YES NO

8/16/2019 Alarma AM375

2/2

g g

 

PDF created with FinePrint pdfFactory trial version http://www.pdffactory.com

http://www.pdffactory.com/http://www.pdffactory.com/