Instrucciones Toque Ingles

7/29/2019 Instrucciones Toque Ingles

1/10

MANUAL INSTRUCCIONES CIRCUITO UN TOQUE

WWW.SOLUCIONESOPEL.COM

INSTALLATION:Raise the trunk lid.Right Display carpeted trunk(Central conVisualizar side (ecu) ceiling. 2 connectorshave one blue and one black. (see photo)contrary to the fuse box)Remove side carpet

PRESENTATION:-1 Complete circuit encased in heat-shrink-8 Crush Quick Connector 3m-1 Plastic clamp-1 Manual


2/10

Then with a hand cojemos black connector and anotherthrew the entire wiring harness away from the connector toremove the pins from within. Would be something like:

After removing the connector and in the same position of thephoto.It can be seen down some numbers are the numericalsequence of connections.

We confirm that the pin 15 color wiringBrown with white stripe.

We removed the black connector by pulling the brown tab inthe direction shown in the picture:


3/10

The number 15 pin connector (jack black)It is the negative mass of all sensors.We need it in the circuit to give order to the roof ecu.

We have to cut the cable about 10 cm ConnectorConnect the two cut cables within a connection that has 3accommodation 3M cable, use 2 accommodations for these two

wires from the circuit and one touch. The union would look like:


4/10

Top connection terminated, the ecu to the car. Cutting andplace in this connection that in the drawing. In the center weput the brown wire white stripe. And we end the black

connector. We assemble and connect to the ecu.

Disconnect the blue connector and dismantle. Asta look likethis:


5/10

Once removed the blue connector. Under you can see the pinnumbers.We look for the pin number n 12. 12V +Cut to 10 cm and connected in the following way.The cable is red. We have T-shaped connecting cable from

the ECU 1 to the touch.((care not to confuse the 12v + wire with the red wireclose. The two are red. Pay attention to the photo))

Once you locate the +12 v wire in the circuit one touch.Cut the wire number 12 to 10cm and connect ecu3m rapid connection as follows:


6/10

Once the connection looks like this:

: We continue with the installation:We look for the blue connector pin n10:

The connection looks like:


7/10

(WARNING Connect the cable from the circuit 1 splash of colorRed to blue stripe ECU roof as shown in the before image. Andthe red wire of the power one touch marked as close, the redstripe blue wire to the car remains unchanged the diagram above)

We continue with another Connect:We return to the blue connector and we have this:


8/10

Now we plug n 23Blue with a green stripe.We cut to 10cm, (same procedure as with the red stripegreen).

Connect the blue with green stripe 1-touch to blue green stripecar ecu.

Then connect the circuit a touch green to blue green stripethat continues to the car.As the following scheme

Once we connected it with another pinNow we look for the blue connector pin 15.Once located violet brown stripe. (notice that seems all welland brown)Cut to 10 cm. this cable have to join you on the circuit 1 violetbrown touch.The scheme is this:


9/10

Once connected the former, there is only 1 cable and the brown1-touch circuit. Watch carefully in brown.(do not confuse violet stripe brown, with brown)

Brown connect directly to screw the vehicle mass. Image below:


10/10

Once connected everything. As the manual.You only have to take the touch of this form with a plasticbracket:

www.solucionesopel.com

Close the carpet and leave it as before. And enjoy one touch toclose and open the roof.In case of emergency. Only by pressing the side opposite to themovement of the roof. Then press again and continue to open orclose smoothly.example:We press remove roof and want to stop.Press close roof 1 single second and stops.If we continue to press again and continues in the direction wewant.any [email protected]

Instrucciones Toque Ingles

Documents

Transcript of Instrucciones Toque Ingles