Notas Técnicas León Supercopa
Transcript of Notas Técnicas León Supercopa
-
8/10/2019 Notas Tcnicas Len Supercopa
1/66
18/12/2006
Information Advise
AIRJACK REINFORCEMENT: After checking rear air jacks supports, some of them
were damaged with little cracks. SEAT Sport offers to the costumers an airjack
reinforcement ref: V4PL011113 to prevent this.
Next we explain the assembly and welding position for this support:
1: Part to be welded. Ref V4PL011113
2: Body position. Weld area viewed from the bottom of the car.
-
8/10/2019 Notas Tcnicas Len Supercopa
2/66
18/12/2006
3: Welded area viewed from the inside of the car.
IMPORTANT:To weld any part of the car is strongly recommended to disconnect
all the electronic elements of the car, (Engine ECU, gate way, inmovilizator, ABS-
CAN, Gear box DSG connector, shifting module, flowmetter), and different parts
that you consider necessary, (suspension, fuel tank, seat, ,,,,).
-
8/10/2019 Notas Tcnicas Len Supercopa
3/66
Nota InformativaInformation Advise
MONTAJE TAPA METLICA AFORADOR: El procedimiento para el correctomontaje de la tapa metlica del aforador es el siguiente:
1. Desmontar la tapa aforador de
plstico de ambos lados deldeposito de combustible.
Tuerca-grapa
Disassemble the plastic cover atthe both fuel cell side.
2. Colocar las tuercas-grapa tal ycomo se muestran en la foto.
Assemble the special nut like isshowed on the picture.
3. Montar la nueva tapa metlicautilizando los dos tornillossuministrados en el kit.
Use the kit bolts to assemble thenew metallic cover.
-
8/10/2019 Notas Tcnicas Len Supercopa
4/66
4. Pasar el conector a traves de la tapametlica y conectarlo a la bomba decombustible. Conectar y apretar elconector de la bomba de gasolinahasta escuchar el clic.Pass the wiring loom through themetallic cover. Connect the fuelpump connector and push until
hearing the click.
5. Atornillar.Screw the bolt
-
8/10/2019 Notas Tcnicas Len Supercopa
5/66
Nota Informativa
Information Advice
Fijacin de baquet para copiloto
En el caso de que un vehculo por los motivos que fuere instale un segundo baquet en
el lugar del copiloto, cuando ste participe en el campeonato Supercopa SEAT Len
debe cumplir con los requisitos abajo indicados.
Con el motivo de no reforzar ni modificar la estructura del vehculo, el soporte del
baquet para copiloto debe ser desmontable, no debiendo estar montado cuando participeen los eventos Supercopa. La fijacin de dichos soportes debe cumplir con la normativa
siguiente:
Fijacin: El anclaje de ste deber efectuarse segn el Anexo J Art. 253
16._Fijacin de los asiento, de forma que durante los eventos Supercopa
SEAT Len slo puede quedar en la carrocera los refuerzos de los pies de
anclaje (de almenos 3mm de espesor y40 cm2 )donde van ancladas las barras de
soporte de las guas de baquet tal y como se muestra en los dibujos del Anexo
J Dib 253-50 al 253-56. Verificacin: El Comisario Tcnico de la Prueba comprobar que los trabajos
han sido realizados correctamente valorando tambin la pulcritud y presentacin
de los mismos.
Dibujos:
-
8/10/2019 Notas Tcnicas Len Supercopa
6/66
Passenger backet fixation
If for any reason a second backet needs to be installed in the passenger side place, and
this car participates in the Supercopa SEAT Leon championship, must fulfil the
following requirements.
In order not to reinforce or modify the vehicle structure, the passengers backet
support must be removable, and it must be dismounted when participating in the
Supercopa events. The supports fixation must fulfil the following rule:
Fixation: The fixation must fulfil the Annexed J Art. 253 -16. _Seats
attachments and supports. In that sense, during the Supercopa SEAT Leon events
are only permitted the fixation reinforcements (3mm thickness and 120 cm2)where
the guides of baquet support bars are fixed as shown in theAnnexed J
drawings 253-50 to the 253-56.
Scrutieneering: The technical Marshal will verify the works have been made
correctly also valuing neatness and presentation
Drawings:
-
8/10/2019 Notas Tcnicas Len Supercopa
7/66
12/05/2006
Nota Tcnica n 1
Coils Wiring loom modification.
1. Disconnect the battery.
2. Disconnect the coils wiring loom of the 2 staples that support of previous coils wiring loom,marked with A in figure 1.
Fig 1
Support B
Original
position
staples A
-
8/10/2019 Notas Tcnicas Len Supercopa
8/66
12/05/2006
3. Disconnect the ground wire (brown) placed under the metallic support and remove the
metallic support, shown in fig 2 (marked with B in fig 1)
Fig 2.
4. Connect the ground wire (brown) in the same place where the support was screwed, using thenew screw.
3. Disconnect camshaft C position sensor (Figure 3) and pass the wiring loom through the
upper part of the butt cover, placing a plastic clamp in the lateral aluminium cover (black)
and return to connect camshaft C position sensor. In figure 3,line of points shows the newlayout.
-
8/10/2019 Notas Tcnicas Len Supercopa
9/66
12/05/2006
Fig 3
New position
Sensor
camshaft C
-
8/10/2019 Notas Tcnicas Len Supercopa
10/66
MANUAL DE MONTAJE RADIADOR SERVODIRECCIN 20092009 STEERING RADIATOR MOUNTING MANUAL
1 de 5
MONTAJE RADIADOR SERVODIRECCIN 2009
2009 STEERING RADIATOR MOUNTING MANUAL
Referencia s /References
DescripcinDescription
ReferenciaReference
CantidadQuantity
Polea pa ra correaPul ley for Belt
V4PL145255 1
Radiador servo-direccinSteering Radiador V4PL422885 1Siletnblock doble espigaRubber mount
V4PT133637 4
Tuerca M6 Din 985Nut M6 Din 985
VN0003090430 8
Tubo entrada radiador servoInlet servo radiador pipe
V4PL422899C 1
Tubo sa lida ra diad or servoOutlet servo radiador pipe
V4PL422892C 1
Desmonta je y Monta je/ Disassembly and Set up:
Las piezas a rriba descritas se monta n en el SEAT Len Supercopa Mk2 sin apena smodifica ciones. Sigan los pas os q ue a continuacin les describimos.
1. Desmonta r el pa rachoq ues, splitter y vaciar de a ceite hidrulico el circuito del radiador.2. Desmontar el rad iador de a ceite, e l serpentn a ctual, los s oportes del rad iador y el tubode entrada y el de salida del radiador. No es necesario desmontar el frontend ni el intercoolerpara es te retrab ajo, pero si se desea hacerlo de forma ms cmoda, desmonte el frontend delcoche.Piezas a desmontar: piezas 23 a 27cata logo 2008, Pg. 62 (ver foto 1)
The par ts above described shou ld be disassembled from the SEAT Leon Supecopa MK2 almost
without modi fications. See below the steps to be followed:
1.
Disassemble the front bumper, the splitter and empty the hydraulic oil from the circuit
and the radiator.
2.
Disassemble the oil radiator , the radiator supports and the inlet and outlet pipe. It is not
necessary to disassemble the complete fronted either the in tercooler. Anyway, for doing this
updating more comfortable for you, it is better to disassembly it.
Parts to be disassembled: parts from 23 to 27 catalogue 2008 , Page 62 (see Picture 1)
-
8/10/2019 Notas Tcnicas Len Supercopa
11/66
MANUAL DE MONTAJE RADIADOR SERVODIRECCIN 20092009 STEERING RADIATOR MOUNTING MANUAL
2 de 5
Foto / Pict ure 1:
1. Utilizar el agujero central en el frontend del soporte derecho del radiador desmontado
(punto B foto 2) como punto de partida para situar y marcar los puntos de anclaje del nuevoradiador. Es conveniente ta par con cinta a dhes iva los agujeros (punto A foto 2) q ue no se va n autilizar.
1. Use from the right support the centred hole of the fronted (point B picture 2) as the startingpoint to situate and mark the new anchoring poin ts. We recommend to cover with adhesive tape
the holes that will not be used anymore (photo 2 point A).
Foto 2/ Picture 2
-
8/10/2019 Notas Tcnicas Len Supercopa
12/66
MANUAL DE MONTAJE RADIADOR SERVODIRECCIN 20092009 STEERING RADIATOR MOUNTING MANUAL
3 de 5
2. Situar el nuevo radiador utilizando el punto B de la foto 2 y marcar los otros 3 puntos deanclaje en el plstico del frontend. Retirar el radiador y realizar los tres agujeros restantes conuna b roca de 6mm. (fotos 3 y 4).
2. Place the new radiator using the point B of the picture 2 and mark in the plastic of thefrontend the other 3 anchoring poin ts. Remove the radiator and make the pending 3 holes with a
drill of (photos 3 & 4)
Foto 3/ Pict ure 3 Foto 4 / Pict ure 4
3. Colocar los y fija r los 4 siletnblock de espiga en los a gujeros rea liza dos . (foto 5)
3.
Set and fix the 4 rubber mount in the holes done. (Picture 5)
Foto 5/ Phot o 5
-
8/10/2019 Notas Tcnicas Len Supercopa
13/66
MANUAL DE MONTAJE RADIADOR SERVODIRECCIN 20092009 STEERING RADIATOR MOUNTING MANUAL
4 de 5
4. Colocar y fijar el radiador nuevo de servo-direccin (foto 6). A continuacin ya se puedecolocar y fijar los tubos de entrada y salida del radiador, colocndolos en la misma posicinque tena n en el frontend a nterior. (foto 7)
4. Set and fi x the new servo radiator (pi cture 6). The outlet and inlet pi pes can be fixedfollowing the same assembl ing done in the fronted disassembled, (Picture 7).
Foto 6/ Pict ure 6 Foto 7/ Pict ure 7
5. Desmontar y montar la nueva polea de la bomba de servo-direccin siguiendo los pasoshabituales. El apriete de los tornillos de la polea se realiza a mano aadiendo fijador detornillos del tipo medio (Locktite 242).Nota: Se recomienda hacer una revisin ocular a la correa y sustituir en caso de pequeaspiedra s a dheridas en el interior del poli V o grieta s externas.
5.
Disassemble and fix the new pulley of the steering pump following the usual steps. The
torque of the bolts from the pulley can be done by hand add ing g lue (Locktite 242).
Note: We recommend making a belt visual revision and substituti ng i t in case of small stones
adhered on the pul ley or external fissures.
6. Aadir a ceite hidrulico has ta el nivel mximo del indicador de la botella de expans in.Poner el motor en marcha durante cinco segundos y volver a pa ra rlo (durante es ta operacin nodeb e g ira rse el volante). Reha cer nivel y repetir el arranque y pa ro en 5 segundos . Reha cer nively ya se puede poner en marcha definitivamente controlando que el nivel de aceite quede entreel mnimo y mximo de la varilla de control cuand o el agua motor se encuentre a 85 C.
6.
Add hydrauli c oil till the maximum expansion bottle level ind icator. Start the engine for 5
seconds and turn off again (the steering wheel should be blocked during this action). Refill oil
level and repeat the starting and stop of 5 seconds. Refill oil level and start definit ively,
controlling the oil level between the minimum and maximum of the oil dipstick when the
temperature of the water is at 85 C.
7.
Montar el Splitter
7.
Assemble the Splitter.
-
8/10/2019 Notas Tcnicas Len Supercopa
14/66
MANUAL DE MONTAJE RADIADOR SERVODIRECCIN 20092009 STEERING RADIATOR MOUNTING MANUAL
5 de 5
8. Retra ba jar el pa rachoq ues ha ciendo una entrada en el lad o izquierdo igua l a la ya hecha enel lado derecho, (foto 8), y monta rlo.
Entre centros de entra da s 382mm
Fondo 45mm Ancho 25mm
8.
Rework the front bumper making a similar hole as the one made in the right side (Picture 8)
and assemble it.
Between holes 382 mm
Depth 45 mm
Wide 25mm
Fot o 8 /Picture 8
Nota s /Notes:
Recordamos consulta r el Manual de l Usua rio para controla r el kilometra je recomenda do devida til de la bomba y correa de servo-direccin. En caso de haberse sobrepasado se debesustituir.
Es recomendable desmontar el radiador de agua e intercooler para la limpieza de losmismos.
Se recomienda utiliza r el lq uido hidrulico des crito en el Ca t logo d e piezas .
We recommend using the User Manual to control recommended mileage of the servo pump
and pu lley. In case of over rep should be substituted.
We recommend d isassembl ing the water radiator and intercooler for its cleaning.
We recommend using the hydrau lic oil mentioned in the spare parts catalogue.
-
8/10/2019 Notas Tcnicas Len Supercopa
15/66
Len Supercopa MK2
Nota tcnica InformativaTechnical Information Note
Fijacin rotula trapecio y regulador cada anterior.
Con motivo de asegurar el blocaje de las tuercas de fijacin de la rtula del trapecio
anterior y regulador de cada, se ha aadido 3 arandelas de freno.
Referencia arandela de freno: VN0002150700 (x3)Posicin y apriete:
Recordar que: Las tuercas tipo aviacin con blocaje por presin y las arandelas de
presin son de un solo uso. Se recomienda realizar los trabajos de ajuste de reglaje en el
taller/box con tuercas normales y sustituir estas por las de tipo aviacin + arandelas
de presin nuevas al finalizar.
12/03/2008
-
8/10/2019 Notas Tcnicas Len Supercopa
16/66
Len Supercopa MK2
Nota tcnica Informativa
Technical Information Note
Ball joint and camber regulation set fixation.
In order to assure the ball joint and camber regulation fixation 3 pressed washers have
been introduced.
Reference pressed washer: VN0002150700 (x3)
Position and torque:
Remember: The aviation nuts and pressed washer only have one time use. Its
advisable to perform the workshop/box setup with standards nuts and to replace it for
aviation plus pressed washer new ones after.
12/03/2008
-
8/10/2019 Notas Tcnicas Len Supercopa
17/66
Len Supercopa MK2
Nota tcnica InformativaTechnical Information Note
Consola fusibles central baja 2008
Con motivo de mejorar el rendimiento de esta pieza, se ha renovado completamente,
mejorando el circuito impreso, el conexionado interno, el esquema de fusibles y se ha
introducido un sistema de luces testigo para el rpido anlisis de estado.
Para adaptar esta pieza a un Len Supercopa Mk2 2006/07 se debe sustituir la consola
fusibles antigua por la nueva, el cable de batera a arranque, el cable de positivo batera
a consola (ahora de batera a conector rpido) y la tapa con su esquema.
Relacin piezas 2008 para realizar la adaptacin:
Consola de fusibles V4PL071035A
Cable consola a arranque V4PL971054A
Tapa batera V4PL801293A
Etiqueta esquema fusibles V4PL000347C
Nota: El casquillo de nylon distancial que determina la altura de la tapa de batera debe
eliminarse.
12/03/2008
-
8/10/2019 Notas Tcnicas Len Supercopa
18/66
Len Supercopa MK2
Nota tcnica Informativa
Technical Information Note
Complete fuses central console 2008
In order to improve the performance of this part, we have developed the new electrical
base, wiring connexion, fuses scheme and fuses indicator led for a faster analysis.
To adapt this part to the Leon Supercup MK2 2006/07 you must substitute the Central
fuses console, the start console wiring loom and the battery cover plus its fuses scheme.
2008 parts to upgrade the car:
Fuses console V4PL071035A
Start wiring loom V4PL971054A
Batter cover V4PL801293A
Adhesive fuses scheme V4PL000347C
Note: The nylon spacer under the old battery cover must be removed.
12/03/2008
-
8/10/2019 Notas Tcnicas Len Supercopa
19/66
Len Supercopa MK2
Nota tcnica InformativaTechnical Information Note
Conjunto filtro de aire 2008
Montado ya en los coches 2008 o con kit 2008, se ha renovado completamente,
mejorando el filtraje y posibilitando una mejor limpieza y mantenimiento.
Este cambio respecto al conjunto filtro anterior, no aporta un cambio o mejora en elrendimiento del motor, por lo que puede ser instalado directamente en los coches 2006 y
2007 como una pieza de sustitucin.
La disponibilidad del filtro antiguo solo ser posible hasta fin de stock.
Para adaptar esta pieza a un Len Supercopa Mk2 2006/07, (No necesaria en los coches
2008 o con kit 2008 porque ya ha sido suministrada) debe solicitar las siguientes piezas
a SEAT Sport:
Referencias piezas 2008 para realizar la adaptacin:
Conjunto caja filtro de aire V4PL133151
Tobera de admisin 1K0129618BM
Conjunto soporte filtro V4PL133171B
Abrazadera 70/90 (x2) VN0004005300
09/04/2008
-
8/10/2019 Notas Tcnicas Len Supercopa
20/66
Len Supercopa MK2
Nota tcnica Informativa
Technical Information Note
Complete air filter 2008
Already mounted on the 2008 cars or previous with 2008 kit, has been completerenovated, improving the performance of this part in cleaning and maintenance.
This change doesnt provide any performance at the engine so it can be installed directly
to the 2006/07 cars like a substitution part.
The old filter part only will be available until end of stock.
To adapt this part to the 2006/07 cars, (No necessary in the 2008 cars or previous with
kit 2008 because it was already supplied) you must order the following parts.
2008 parts references to adapt it:
Complete air box V4PL133151
Inlet air duct 1K0129618BM
Air filter box support V4PL133171B
Clamp 70/90 (x2) VN0004005300
09/04/2008
-
8/10/2019 Notas Tcnicas Len Supercopa
21/66
Len Supercopa MK2
09/06/2008
Nota tcnica InformativaTechnical Information Note
Kit junta reparacin pinza de freno
Tras las mejoras realizadas en las pinzas de freno para el 2008 en adelante, los kits de
reparacin a utilizar quedan de la siguiente forma:
Coches fabricados hasta noviembre/diciembre 2007 utilizan las pinzas refs: CP7061-
6S0LRD:SEAT y CP7061-7S0LRD:SEAT
Kit de juntas a montar en estas pinzas, Ref AP: CP4519-CEJ: SEA
Ref SEAT Sport: V4PL698471
Coches fabricados desde enero 2008 utilizan las pinzas refs: CP7081-4S0LRD:SEA y
CP7081-5S0LRD:SEA
Kit de juntas a montar en estas pinzas: Ref. AP: CP4518-CEJ
Ref. SEAT Sport: V2ML698471A
Las diferencias entre las pinzas CP7061 Y CP7081 es el diseo del canal de la junta de
goma, a la que se le ha aplicado un ngulo para evitar el knock-off de los pistones y el
mejor cierre tanto en baja presin y temperatura como en alta. La utilizacin de estas
juntas Racing permiten un mayor margen de seguridad en las perdidas de lquido en
fro.
En todos los casos las pinzas estn marcadas a lser en el cuerpo del mismo por lo quees fcil comprobar el tipo de juntas que debe utilizarse.
-
8/10/2019 Notas Tcnicas Len Supercopa
22/66
Len Supercopa MK2
09/06/2008
Nota tcnica InformativaTechnical Information Note
Set of calliper gaskets
After the improvements done from 2008 front callipers, the set of calliper gaskets to use
will be in the following form:
Cars build until October / December 2007 used the front callipers refs: CP7061-
6S0LRD:SEAT y CP7061-7S0LRD:SEAT
Set of calliper gaskets to fit: Ref AP: CP4519-CEJ: SEA
Ref SEAT Sport: V4PL698471
Cars build from January 2008 used the front calliper refs: CP7081-4S0LRD:SEA yCP7081-5S0LRD:SEA
Set of calliper gaskets to fit: Ref. AP: CP4518-CEJRef. SEAT Sport: V2ML698471A
The differences between this two front callipers CP7061 Y CP7081 is the design of the
gasket canal. They have been implemented an angle to avoid Knok-off on the pistons
and the best closure in high pressure and temperature as in low. The utilization of these
Racing gaskets allows having a greater safety margin in the leakage in cold conditions.
In all the cases the front brake calliper are the laser marked on the body calliper and is
easy to check the gaskets type to be used.
-
8/10/2019 Notas Tcnicas Len Supercopa
23/66
Inscrito en el registro mercantil de Barcelona, Tomo 33.081, Folio 32, Hoja 223.602. NIF: A-62390653
NOTA MODIFICACIN PASO RUEDA
An no siendo mec nicamente pos ible que el neumtico utilizad o en la
Supercopa SEATLen 2006 llegue a conta cta r con la cha pa del pas o de rueda s, s e
permite recortar la chapa del paso de ruedas en los puntos indicados en las siguientes
imgenes.
Although it is not phys ically poss ible tha t the tire us ed in Supercopa SEATLeon
2006 contacts with the bod yshell, it is a llowed to trim the plate o f the wheelhouse in the
indicated points in the following pictures :
Zona a recorta r / Area to be cut
Vista zona recortada / View of the cut a rea
SUPERCOPA LEON
Abrera ,23 d e Agosto d el 2006
-
8/10/2019 Notas Tcnicas Len Supercopa
24/66
Nota Informativa
Information Advice
Fondo plano central
Os adjuntamos complemento al Manual del Usuario y al Catlogo de Piezas de la
Copa SEAT Len 2007. Esta modificacin de pieza ser de aplicacin en las piezas derecambios de forma inmediata.
La nueva referencia de la pieza a solicitar es V4PL825257CFondo plano central.
A continuacin les mostramos un croquis del recorte a realizar para la correcta
transformacin de la pieza, mejorando as la refrigeracin en el vano motor. La manta
trmica suministrada de origen en la zona de la NACA debe seguir en la misma
posicin.
-
8/10/2019 Notas Tcnicas Len Supercopa
25/66
Central flat bottom
We enclosed complement of the User Manual and the Part Catalogue of SEAT
Leon 2007 Cup. This part modification will be applied in the spare parts production
immediately.
The new part reference is V4PL825257C Central flat bottom.
Following is showed a picture with the area to be cut off, improving the
refrigeration in the engine cockpit area. The thermo protection added on the originalpart in this area must be keep in place.
-
8/10/2019 Notas Tcnicas Len Supercopa
26/66
Nota Informativa
Information Advice
Entrada de aire piloto
Os adjuntamos complemento al Manual del Usuario y al Catlogo de Piezas de la
Copa SEAT Len 2007. Este complemento ser de aplicacin a partir de la carrera de
Pau y para el resto de la temporada.
La referencia de la pieza completa a solicitar es V4PL817833. Con su compra
recibir una platilla para su correcto posicionamiento en el techo del vehculo. A
continuacin les mostramos la imagen disponible en las actualizaciones del Catlogo de
Piezas y Manual del Usuario.
-
8/10/2019 Notas Tcnicas Len Supercopa
27/66
Air intake driver refrigeration
We enclosed complement of the User Manual and the Part Catalogue of SEAT
Leon 2007 Cup. This complement will be applied from the Pau race and for the rest
of the season.
The reference of the complete part to ask for its V4PL817833. With it you will
receive a pattern for the correct positioning in the cars roof. Find bellow the image
available in the update of the User Manual and Parts Catalogue.
-
8/10/2019 Notas Tcnicas Len Supercopa
28/66
Nota InformativaInformation Note
Verificacin del mazo bomba de caudal adicional.
Este mazo a verificar se encuentra dentro del depsito de gasolina, en el lado piloto y
conectado a la bomba auxiliar que all se encuentra.
El cable de color marrn (positivo 12v) debe estar montado en el emplazamiento n 1
del conector y el amarillo en el n 2 . Dando contacto se puede comprobar que el cable
marrn es positivo 12v antes de cerrar el deposito. (recordar que es una seal modulada yque vuelve a 0 en cuanto se alcance la presin de gasolina asignada).
Additional wiring loom check.
This wiring loom its placed inside of the fuel cell, driver side and connected to the
additional fuel pump.
The brown cable (positive 12v) must be connect at the n 1 plastic connector place and
the yellow at the n 2 place. It is possible to check if the brown cable have 12 volts
when the contact switch is on before to close the fuel cell. (remember that the 12v signalis modulated by the ECU and will be 0 when the fuel pressure is done.)
-
8/10/2019 Notas Tcnicas Len Supercopa
29/66
15-5-06
Nota Tcnica n 3
Proteccin Escape
Con la informacin obtenida durante los primeros test colectivos del nuevo
SEAT Len Supercopa Mk2, y para evitar posibles incendios de goma deneumtico acumulada entre el tubo de escape y el fondo plano, se permiteenvolver el tubo de escape con venda trmica.
Las zonas mas recomendables de proteger son:
En los vehculos equipados con fondo plano es mas difcil observar unaposible perdida de aceite o goma de neumtico acumulada, por lo que serecomienda desmontar el fondo plano con cierta frecuencia.
-
8/10/2019 Notas Tcnicas Len Supercopa
30/66
09/05/2006
Nota Tcnica n 1
Modificacin recorrido mazo cables bobinas.
1. Desconectar la batera.
2. Desgrapar el mazo de cables de bobinas de las 2 grapas de soporte del mazo anteriores a las
bobinas. Marcado con A en la figura 1.
Fig 1
Grapas A
Trazadooriginal
Soporte B
-
8/10/2019 Notas Tcnicas Len Supercopa
31/66
09/05/2006
3. Desconectar el cable de masa colocado sobre el soporte y eliminar el soporte metlico.Marcado con B en la fig 1, y figura 2
Fig 2.
4. Desconectar el sensor de posicin de rbol de levas C (Figura 3) y pasar el mazo de cablespor la parte superior de la tapa de culata, colocando una brida de plstico en la tapa de
aluminio lateral (negra) y volviendo a conectar el sensor de posicin de rbol de levas. En la
figura 3, se observa en lnea de puntos, el nuevo trazado.
Fig 3
Sensor rbolde levas C
Nuevo trazado
-
8/10/2019 Notas Tcnicas Len Supercopa
32/66
09/05/2006
5. Conectar el cable marrn de masa aprovechando la misma rosca donde estaba atornillado elsoporte, utilizando el nuevo tornillo suministrado por SSp.
-
8/10/2019 Notas Tcnicas Len Supercopa
33/66
24/10/2006
Nota informativa
Information advise
LIMPEZA DEL INTERCAMBIADOR Y DEL RADIADOR:
Se recomienda a todos los equipos, que desmonten, enderecen laminillas ylimpien ambos despus de cada evento o despus de cada carrera o entreno
en el que hayan sufrido una salida de pista, para asegurar la refrigeracin y
prestaciones mximas del motor, ya que este se protege de los
sobrecalentamientos, tanto de aire de admisin como de lquido
refrigerante, disminuyendo su potencia.
________________________________________
INTERCOOLER AND RADIATOR CLEANING:
It is recommended to all the teams, that disassembles and clean both after
each event after each race or practice session in which they have exit the
track, to assure the refrigeration and maximum performance of the engine,since it auto protects from intake air and cooling liquid overheating by
diminishing his power.
-
8/10/2019 Notas Tcnicas Len Supercopa
34/66
Len Supercopa MK2
ota tcnica Informat ivaTechnical Information Note
PROTECION TRMICA PINZA FRENO ANTERIOR
SEATSport recomienda utilizar una proteccin trmica pa ra evita r parte de
la transferencia de temperatura disipada de la pastilla de freno al lquido de la
pinza de l SEATSupercopa Len.
Esta placa trmica consigue disminuir la temperatura del lquido de freno en
pinza a lrededor de 60C.
Se aconseja su uso en los circuitos con trazados especialmente duros para
los frenos. La referencia q ue es posible montar es la s iguiente.
V4P L698474 JUEGO DE PROTECCIONES TERMICAS CALIPERS - 35/kit (4 pla ca s)
_____________________________________________________________________
FRONTCALLIPER THERMAL PROTECTION
SEAT Sport recommends to use a thermal protect ion pla te to a void the
temperature transference from pads to the ca lliper liquid on S EATSupercopa Leon.
This thermal plate reduce the brake liquid temperature from the ca lliper
a round 60C.
We recommend to use on circuits ha rd in braking a nd s pecially heavy for the
ca r. The reference a llowed to be fitted in the ca rs is:
V4P L698474 KITOF CALLIPER THERMAL PROTECTION 35/kit (4 pieces)
10/06/2010
-
8/10/2019 Notas Tcnicas Len Supercopa
35/66
Len Supercopa MK2
Nota tcnica Informat iva
MANTENIMIENTO TUERCAS DE RUEDA
Recorda torio s obre el mantenimiento de la s tuercas de rueda , ya des crito en el Manual del Usuario
MANTENIMIENTO:
MANTENIMIENTO
DENOMINACINCadacarrera
Cada2000 km
Revisin6000 km
Revisin10000 km
COMENTARIOS
SUSPENSION
Tuercas de rueda Sust. Comproba r dependiendo del tipo de prue
Mang ueta Rev. Comproba r peridicamente si ha y algunade un accidente.
Rodamient ruedasanteriores
Sust. Importante tener en cuenta la ta bla de pa
Rodamientoruedasposteriores
Sust. Importante tener en cuenta la ta bla de pa
Rotulas esfricas engeneral
Sust.
Conjunto Amortiguadores Sus t. Rea lizada so lo por SEATSport
*para ms informacin sobre otros mantenimientos ver apartado Mantenimiento del Manual Usuario 2010 d isponi ble en la we
PAR DE APRIETE:
SUSPENSIONES
Tuercas de rueda 90 Nm + grasa de temperatura
04/08/2010
-
8/10/2019 Notas Tcnicas Len Supercopa
36/66
Len Supercopa MK2
Technical Information Note
WHEEL NUTS MAINTENANCE
Wheel nuts ma intenance a nd torq ue reminder, already been expla ined in the User Manual 2010.
MAINTENANCE:
MANTENANCE
DENOMINATIONEACHRACE
EACH 2000KM
EACH 6000 KM EACH 10000 KM C
SUSPENSIONWheel nuts Sust . Check if a endurance raUpright Rev. Check fissures if a ny acFront whee lhup bea ring Sust . Torque bolt is very impRea r whee l hup bea ring Sust . Torque bolt is very impSpheric ba ll Sust.Shock a bsorbers Sus t. Only done by SEATSpo
*for more information about mileage maintenance and torque bolt s consult the 2010 User Manual on the web side seat-sport.c
SPECIFIC TORQUES:
SUSPENSIONWheel nut 90 Nm Plus temperat ure grea se
04/08/2010
-
8/10/2019 Notas Tcnicas Len Supercopa
37/66
Len Supercopa MK2
MECHATRONICA INFORMATION and UPDATE.
Mechat ronica S pare parts a va ilability:
SSp Reference ID (VAS) Gea r box ID Comment From
VL1E325025 FXX_Supercopa SSP xx xxx Large ratios 2006
VL1E325025A FYY_Supercopa SSP xx xxx C Short ratios 2008
VL1E325025B agr DSG SSP xx xxx CR Short ratios + fa st shifting 2010
Mechat ronicas Updat e:
From now, a ll Mecha tronicas provided for SEATSport a s a spa re pa rt will be
ada pted on the rolling bench with the ba sic adjustment done.This process will avoid any ada pta tion problem and the pa rts could be delivered to
the customers tha t do not ha ve the VAS program to a da pt them.
VAS Mechat ronicas ada pta tion process:
1. Clean faults
2. Program the DSG software.
3. 06 End. Contact a nd ba ttery reset.
4. 07 Codifica tion
a . code 20 with VAS, code 0000020 with VAGCom.
5.
06 End. Contact a nd ba ttery reset.6. Clean the faults
7. 04 Basic adjustment (block 65-61-60)*
8. 06 End. Conta ct and ba ttery res et . (IMPORTANT)
* If the mechatronica had adapted or is used, a basic adjustment is not necessary
but recommendable.
2010 DSG s oftwa re
Wha t to feel on the agr so ftwa re different from sta nda rd FYY.
Action Improvement Other advanta gesUPSHIFT Fas ter in the action
Immediacy on the a ction
Flat in the eng ine boos t
Precision
Time
DOWNSHIFT Immediacy on the action
Agg ressive on the a ction
Clutch drop off more ag gressive
Brake sa ving
Reduction point precision
Others Launch control: the sa me
Firs g ea r in spin cas es: the sa me
Automatic S function: the sa me
IMPORTANT: This software does not give himself time. A gain in lap time depends on
the drivers driving.
14/06/2010
-
8/10/2019 Notas Tcnicas Len Supercopa
38/66
Len Supercopa MK2
MECHATRONICA INFORMATION and UPDATE.
Mechat ronica S pare parts a va ilability:
SSp Reference ID (VAS) Gea r box ID Comment From
VL1E325025 FXX_Supercopa SSP xx xxx Large ratios 2006
VL1E325025A FYY_Supercopa SSP xx xxx C Short ratios 2008
VL1E325025B agr DSG SSP xx xxx CR Short ratios + fa st shifting 2010
Mechat ronicas Updat e:
From now, a ll Mecha tronicas references provided for SEATSport a s a spa re pa rt will
be a da pted on the rolling b ench with the ba sic ad justment done.
This process will avoid any ada pta tion problem and the pa rts could be delivered to
the customers tha t do not ha ve the VAS program to a da pt them.
As a rolling VWGroup reference, (no ca ta logue reference) Mecha tronicas ha rdwarewill change, unt il now wa s 02E927770AE a nd now will be 02E927770AD.
This change does not a ffect at the Mechat ronica beha viour a nd bo th ca n be fitted
on the SEATSupercopa DSG gea r box.
About the Mecha tronicas tha t Importers ha ve in stock can be a da pted from him selfin the moment when a re fitted or, can be send to SEATSport to be a da pted there.
This a da pta tion will be d one without cost. (Only shipment cos ts).
In cas e tha t the new agr softwa re is programmed, SEATSport will identify the
gea r box with a R sta mped then of the exist ing ID number:
(Sa mple: SSP 848 236 C R).
VAS Mechat ronicas ada pta tion process:
1.
Clean faults2. Program the DSG software.
3. 06 End. Contact a nd ba ttery reset.
4. 07 Codifica tion
a . code 20 with VAS, code 0000020 with VAGCom.
5. 06 End. Contact a nd ba ttery reset.6. Clean the faults
7. 04 Basic adjustment (block 65-61-60)*8. 06 End. Conta ct and ba ttery res et . (IMPORTANT)
* If the mechatronica had adapted or is used, a basic adjustment is not necessary
but recommendable.
14/06/2010
-
8/10/2019 Notas Tcnicas Len Supercopa
39/66
Len Supercopa MK2
2010 DSG s oftwa re
Wha t to feel on the agr so ftwa re different from sta nda rd FYY.
Action Improvement Other advanta ges
UPSHIFT Fas ter in the action
Immediacy on the a ction
Flat in the eng ine boos t
Precision
Time
DOWNSHIFT Immediacy on the action
Agg ressive on the a ctionClutch drop off more ag gressive
Brake sa ving
Reduction point precision
Others Launch control: the sa me
Firs g ea r in spin cas es: the sa me
Automatic S function: the sa me
IMPORTANT: This software does not give himself time. A gain in lap time depends on
the drivers driving.
14/06/2010
-
8/10/2019 Notas Tcnicas Len Supercopa
40/66
Len Supercopa MK2
NOTA TCNICA
PROCEDIMIENTO COMPROBACION PRECARGA DIFERENCIAL AUTOBLOCANTE
A continuacin informamos del procedimiento pa ra la comproba cin de los valoresde precarga del diferencia l autob locante de l cambio de velocidades DSG del LenSupercopa Mk2.
1) Las comproba ciones pueden ha cerse ta nto en fro como en ca liente.2) Coloca r el vehiculo sobre a irjacks y colocar sus seguros.3) Asegurarse q ue el motor ha sido parado por el procedimiento correcto, de lo
contrario podra fa lsea rse el valor. El procedimiento, por orden, es elsiguiente
a .
Motor en marcha (so lo un momento pa ra a segurar Neutral).b. El displa y del mod ulo de volante indica N (neutral)c. Interruptor de conta cto off.d. Interruptor de ba tera off..
4) Fija r una d e las ruedas delanteras , (se puede ha cer a mano), coloca r unallave dinamomtrica de aguja en el tornillo del pa lier (centro de rueda ) de larueda contraria y gira r en sentido hora rio fijndose en el par de a rra stre. Losvalores deb en esta r seg n la siguiente ta bla:
PRECARGA DIFERENCIAL
Frio 75 15% Nm
Nuevo / Revisado* Caliente 60 15% NmFrio 60 15% Nm
UsadoCaliente 40 15% Nm
* Tambin se considera nuevo cuando se ha revisa do y tod ava no harodado.
INFORMACIN ADICIONAL:
En el montaje de ta ller el diferencial a utobloca nte se ta ra entre 50 y 60 Nm deprecarga . El aumento de preca rga (hasta 80 Nm max) medido en la rueda esdebido a los rozamientos de diversa s piezas .
Es aconsejable revisa r el autobloca nte cuanto la precarga disminuye de 20Nm en fro y 10 Nm en ca liente.
15/01/2010
-
8/10/2019 Notas Tcnicas Len Supercopa
41/66
Len Supercopa MK2
TECHNICAL NOTE
SLIP DIFERENTIAL CHECKING PROCEDURE
See bellow the SEATLeon MK2 DSG g ea r box s lip differentia l PRELOAD procedure.
1) Checks ca n be done in cold or in wa rm conditions.2) Up the ca r with the a ir-ja cks and fix it.3) Take care tha t the ca r engine was s topped through the correct procedure, if
not the rea d va lue could not be true. The procedure order is a s following.a . Sta rt the engine to as sure tha t the shift module indicates N
neutral.
b.
Put the shif module in N neutra l.c. Switch off the contact switch.d. Switch off the main sw itch.
4) To fix one of the front wheels (you can do it by ha nd), put a needledyna mometric tool on the drive sha ft bolt (wheel center) and turn the too l inclock wise sense to mea sure the value. The value must be a s following:
SLIP DIFFERENTIAL PRELOAD
Cold 75 15% NmNEW/ Reb uilded*
Hot 60 15% NmCold 60 15% Nm
Used Hot 40 15% Nm
* Revised is considered as new if it ha s never been used.
ADDITIONAL INFORMATION:
When the slip differentia ls a re repaired on the workshop the preload va lueapplied is between 50 and 60 Nm (differentia l disass embled from the gea rbox). The preload value tha t you ca n rea d on the wheel centre increa se (max80 Nm) beca use the other parts a re frictioning.
It is advisa ble to check the s lip differential when the preloa d decrea se lesstha n 20 Nm in cold a nd 10 Nm in warm conditions.
15/01/2010
-
8/10/2019 Notas Tcnicas Len Supercopa
42/66
Len Supercopa MK2
Nota tcnica InformativaTechnical Information Note
Cableados deps ito de combust ible
Debido a la diversidad de ga solinas con caractersticas distintas a la Standa rd 98
sin plomo utilizada s en el Len Supercopa en los distintos pases donde el Len
Supercopa MK2 participa, s e han da do ca sos de endurecimiento y retraccin del
recubrimiento aislante del cable elctrico que se encuentra en el interior del
depsito de ga solina.
Recomendamos comproba r el esta do de los cablead os d el interior del deps ito de
combustible. Si el a specto corresponde a l de la foto 1, no es necesa rio sustituirlo,
por el contra rio, si el as pecto es e l de la foto 2, s e deb er sustituir.
Foto 1: BIEN (2008) Foto 2: MAL (2008)
SEATSport ha fabricado nuevos los ca blea dos del interior del depsito utiliza ndo
un nuevo ca ble tcnico, f cilmente reconocible por ser de colores d iferentes .
Foto 3: NUEVO 2009
21/01/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
43/66
Len Supercopa MK2
PROCEDIMIENTO DE MODIFICACION.
Pos ibilida d A: Reempla za r los cab les Ud. mismo.
1. Pida los ca bles (Foto 4) a S EATSport, sin coste a lguno, con las siguientes
referencias:
Ref: V4PL971755
Ref: V4PL971897A
2. Desmonte la bomba principal del deposito de combustible y sustituya el
mazo de la bomba a uxiliar des oldando y vuelva a s oldar el nuevo mazo:
a . Color azul nuevo ma zo en el lad o izq uierdo (A en la foto 5)
b. Blanco en el derecho (B en la foto 5).
Foto 4 Foto 5
Posibilidad B: Desmonta r la bomba principal del interior del depos ito, vaciarla de
ga solina y envia rla a SEAT Sport para la sus titucin del cablea do (Foto 6),
indicando el nmero de chas is y equipo a l que pertenece.
Nota:Si la sustitucin de los mazos ya fue hecha por SEATSport o si es te traba jo
ya fue realizado en el vehculo que obra en su poder, encontrar una marca
amarilla en la pa rte superior de la bomba .
Foto 6
21/01/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
44/66
Len Supercopa MK2
Nota tcnica Informativa
Technical Information NoteFuel ta nk wiring loom
Due to the variety and different characteristics of petrol Standard 98 lead free
used in the different Supecopa Len championships over the countries where the
Supercopa Len MK2 is pa rticipating, we ha ve observed tha t in some ca ses exists a
process where the wire is getting harder and there is a retraction of the electrical
cab le situated inside of the petrol tank.
We recommend to check the ca bles inside the petrol tank. If the a ppea rance is like
the Picture 1, it is not necessary to change it, but if looks like Picture 2 it must be
replaced.
Picture 1 OK (2008) Picture 2 WRONG (2008)
SEAT Sport has produced cab les for inside of the tank using a new technical
specification ca ble, ea sy recognizable beca use there a re two different colours.
Picture 3 NEW2009
21/01/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
45/66
Len Supercopa MK2
PROCEDURE OF MODIFICATION:
Option A: Replace cable by yourself.
1.
Ask for the two ca bles , for free to a ll the customers, from the picture 4 toSEATSport with the following references :
Ref: V4PL971755
Ref: V4PL971897A
2. Disassemble the main petrol pump from the tank and substitute the
auxiliary pump wiring loom unwelding and welding it again with the new
wiring loom. The process will be blue colour from the new wiring in the left
side (A in Picture 5) and white on the right s ide (B in the Picture 5).
Picture 4 Picture 5
Option B: Disa ss emble the ma in pump from the ta nk (pa rt Picture 6), empty it from
petrol and send it to SEATSport indica ting the n of chas sis a nd the na me of the
tea m. SEATSport will make the subst itution o f the wire.
Note: If SEATSport made a lrea dy this subst itution in the ca r, a yellow ma rk will be
in the upper part of the pump.
Picture 6
21/01/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
46/66
Len Supercopa MK2
Nota tcnica InformativaTechnical Information Note
Indicador nivel de ga solina deps ito Supercopa Mk2Fuel tank level indi cator for Leon Supercopa MK2
Para conocer la ca ntidad de litros rea les de combustible, en el cana l Fuel Leveldel Das hboard MXL de AIM, es necesa rio realizar una modificacin en e l cab leadode la bomba de combustible.
To know the fuel level more exactly on the MXL - AIM dashboard , i t is necessary tocarry out a flow pump wiring loom modifi cation.
PROCEDIMIENTO DE MODIFICACION DEL CABLEADOWIRING LOOM MODIFICATION PROCEDURE
1. Desmonte la bomba principa l del deps ito de combust ible (Foto1)Disassemble the main fuel tank flow pump (Photo1
Foto1. Bomba principal de combustib le
Foto1. Main flow fuel pump
12/01/2011
-
8/10/2019 Notas Tcnicas Len Supercopa
47/66
Len Supercopa MK2
2. Corte el cable a zul solda do en el termina l centra l (Foto 3).Cut the blue cable welded on the centra l pin. (Photo 3)
Foto2. Cableado bomba principalPhoto 2. Main pump wiri ng
Cortar
Foto3. Cableado bomba principalPhoto 2. Main wiri ng loom
3. Eliminar el cable sobrante.Elimina te the blue cable.
12/01/2011
-
8/10/2019 Notas Tcnicas Len Supercopa
48/66
Len Supercopa MK2
PROCEDIMIENTO DE CONFIGURACIN DEL CUADRO DE INSTRUMETOSDASHBOAR CONFIGURATION PROCEDURE
En Race Studio, mediante Custom Sensors Ma nager (Foto 4), crear un Custom
Sensor (Foto 5).On the Race Stud io, through the Custom Sensors Manager (Photo 4), to create aCustom Sensor. (Photo 5).
Foto 4. Race Stud io Photo4. Race Stud io
Foto 5 . Customize Sensor Photo 5. Customize Sensor
12/01/2011
-
8/10/2019 Notas Tcnicas Len Supercopa
49/66
Len Supercopa MK2
Opcin 1: Crea r Custom Sensor tipo, linealizado por Sea t Sport. La linea liza cin esla siguiente:Option 1: Create a Custom Sensor type, linearization by SEAT Sport. The
linearization is the following:
mV Litros
1 2167 02 2402 53 2645 104 2907 155 3072 206 3248 25
7 3383 308 3461 359 3588 40
10 3685 4511 3753 5012 3831 5513 3880 6014 3939 65
Opcin 2:Crea r Custom Sensor seg n linealizacin especifica para ca da coche:
- Vaciar depsito de combustible totalmente- Conecta r al coche y a cceder Online en Race S tudio. Activa r va lor en directo
en mV. (arriva a la derecha).- Llenar 5 litros de combustible y comprobar valor devuelto en mV que
aparece en el cana l Fuel level , en Race Studio. Ir aad iendo de 5 en 5litros ha sta llega r a completar los valores de toda la ta bla, ha sta 65 litrosanotando el va lor correspondiente cad a 5 litros a ad idos.
Option 2:Create a Custom Sensor by linearization specific for each car:
- Drain the fuel tank complete.- Plug in the lap top to the car Onli ne trough the Race Studio. Click on the mV
but ton to see the value in mV.- Fil l up 5 l itres in the tank and check the return value in mV that appears over
the Fuel level channel. Fil l up the tank 5 l it res more, check the value andwrite it each 5 l itters. Follow th is process until the fuel cell is full (until 65litres).
Guarda r customizacin de sensor y as igna r a Cana l auxilia r. Envia r nuevaconfiguracin de ca nales.
12/01/2011
-
8/10/2019 Notas Tcnicas Len Supercopa
50/66
Len Supercopa MK2
Save the sensor customization and assign a auxil iary Channel. Send the newconfiguration to the dashboard.
Finalmente el proceso se ha terminado. Ahora si lo desea puede configurar una alarma
de nivel de gasolina. (Aconsejable entre los 10 y 5 ltimos litros)
Finally the process is finished. You can activate one of the alarms available for the fuellevel. (Advisable between 10 or 5 last litres)
12/01/2011
-
8/10/2019 Notas Tcnicas Len Supercopa
51/66
Len Supercopa MK2
Nota tcnica Informativa
Technical Information NoteEvoluciones 2009 Len Supercopa MK2
Para la temporada 2009 se ha n evolucionad o las siguientes piezas :
Descripcin Referencia Cantida d SC/EUROCUP PVP/UD.
SERVODIRECIN
Polea para correa (mayor dimetro) V4PL145255 1 Obliga torio 32,07
Radiador servodireccin V4PL422885 1 Obliga torio 94,18
Siletnblock dob le espiga V4P T133637 4 Obliga torio 0,75
Tuerca M6 Din 985 VN0003090430 8 Obliga torio 0,12
Tubo e ntrada radia dor servo V4PL422899C 1 Obliga torio 60,00
Tubo s a lida ra diad or servo V4PL422892C 1 Obliga torio 60,00
SUSPENSION
Ba rra esta b. Pos t 22x5 (25% + dura) V4PL511407B 1 Set up 210,00
Muelle de 100 Nm VN0020065600 2 Set up 67,50
Servo-direccin:Se ha sustituido el radiador de servo-direccin por otro de mayorcapacidad disminuyendo la temperatura del aceite hidrulico y mejorando elcomporta miento en cond iciones extremas .La polea, de mayor dimetro, evita sobrepasar su rgimen mximo cuando sea lcanza n valores de rgimen motor por encima del mximo esta blecido.En el manual de montaje de las piezas de direccin 2009 se explica los pasos aseguir pa r el correcto monta je.Esta s piezas de servo-direccin s on de uso ob liga torio en la Supercopa y Eurocopa .En cas o de s olicitarla s a ntes del 28/02/2009 se efectuar un descuento del 15%.Barra estabilizadora: Con la intencin de aumentar las posibilidades de reglajes,SEATSport pone a dispos icin de los clientes una ba rra esta bilizadora posterior demayor rigidez a la to rsin.La posicin ms bland a de la nueva ba rra es un 15% ms rgido que el punto ms
rgido de la ba rra ya existente (V4PL511407A). Las dos ba rra s sern a ptas paracompetir en los campeonatos como pieza de catlogo y por tanto como pieza dereglaje.
Muelle de suspensin 100 Nm: Con la intencin de aumentar las posibilidades dereglajes SEATSport pone a disposicin de los clientes un muelle de 100 Nm parada r ms posibilidades de regla je.
Muelles de s uspensin:En el 2009 SEATSport modifica e l Manua l del Usua rio y laFicha Tcnica pa ra permitir el monta je de los d istintos muelles de sus pens incatalogados en cualquiera de los dos ejes, a excepcin del 250/60/70, solo para
el eje anterior.
26/01/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
52/66
Len Supercopa MK2
Nota tcnica Informativa
Technical Information NoteImprovements 2009 Len Supercopa MK2
See below the 2009 season development of the following spares pa rts:
Description Reference Qty SC/EUROCUP Unit Price
STEERING
Pulley for be lt (bigg er diameter) V4PL145255 1 Compulsory 32,07
Oil servo ra dia tor V4PL422885 1 Compulso ry 94,18
Rubber mount V4PT133637 4 Compulso ry 0,75 Nut M6 Din 985 VN0003090430 8 Compulso ry 0,12 Inlet pipe servo rad iad or V4PL422899C 1 Compulso ry 60,00 Outlet pipe servo radiator V4PL422892C 1 Compulso ry 60,00
SUSPENSIONRea r a nti roll ba r 22x5 (25%+ ha rder ) V4PL511407B 1 Set up 210,00 Spring o f 100 Nm VN0020065600 2 Set up 67,50
Steering servo: The oil servo cooler has been subst ituted by a nother of bigg ercapacity, improving the temperature of the hydraulic oil and improving the
reliab ility in extreme conditions .The pulley, with b igger diameter, prevents steering pump overrevs when you a renea r the maximum rpm engine.See the correct set-up of the steering s ervo 2009 in the mount manual.Steering servo parts will be compulsory in Supercopa and Eurocopachampionships.Specia l Offer: for orders before 28/02/2009 will have a dis count of 15%.
Rear Anti roll bar: With the a im of improving the set up poss ibilities , SEATSportoffers a rear anti roll bar with a ha rder rigidity. The s often point of the new a nti rollba r is 15% ha rder tha t the existing ha rder point of the current a nti roll bar
(V4PL505407A). Both a nti roll bars will be a llowed a s s etup in both cha mpions hipsand a vailable in the cata logue.
Suspension spring 100 Nm: To enlarge the possibilities of setups , SEAT Sportoffers a spring of 100 Nm.
Springs: The S EATSport 2009 User Manua l and Technica l Da ta will be mod ifiedallowing the setting of all catalogued springs for both axels with the exception ofthe spring 250/60/70 only a llowed in the front a xle.
26/01/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
53/66
Len Supercopa MK2
Nota tcnica Informativa
Technical Information Note
ACTUALIZACIN GUIAS DE ASIENTO SUPERCOPA
Por cambios en la produccin del fabricante se cambiado de gua de asiento. A
continuacin se informa de las referencias de guas de asiento asociadas segnreferencia de asiento en el caso que se deba hacer un cambio.
VEHICULOS CON ASIENTO REFERENCIA: (coches anteriores Abril 2007)
Ref. OMP: HA / 718 / N (ver etiqueta asiento)Ref. SEAT: V4PL881019C= 470 mm.
Ahora se monta con las siguientes referencias:
Referencias SEAT: soporte V4PL881689A (x1)+ arandela V131420045 (x4)+ tornillo VN0001906739 (x4) (M8x30)
VEHICULOS CON ASIENTO REFERENCIA: (posterior Abril 2007)
Ref. OMP: HA / 743 / N (ver etiqueta asiento)Ref. SEAT: V4PL881019AC= 500 mm
Se monta la guia:
Ref. SEAT: soporte V4PL881689A (x1)
09/03/2010
-
8/10/2019 Notas Tcnicas Len Supercopa
54/66
Len Supercopa MK2
RACING SEAT BRACKET UPGRADING
Because the changes done by the manufacturer the racing seat bracket has beenchanged. Following there is the information about the racing seat bracketassociated according to the racing seat reference.
RACING SEAT WITH THE REFERENCE: (cars previous April 2007)
Ref. OMP: HA / 718 / N (see seat label)
Ref. SEAT: V4PL881019C= 470 mm.
Now with the following references:
SEAT references: bracket V4PL881689A (x1)+ washer V131420045 (x4)+ bolt VN0001906739 (x4) (M8x30)
RACING SEAT WITH THE REFERENCE: (cars later April 2007)
Ref. OMP: HA / 743 / N (see seat label)Ref. SEAT: V4PL881019AC= 500 mm
Now with the following references:
SEAT reference:racing seat bracket V4PL881689A (x1)
09/03/2010
-
8/10/2019 Notas Tcnicas Len Supercopa
55/66
Len Supercopa MK2
Nota tcnica InformativaTechnical Information Note
Cana lizadores a ire Freno y Radiadores
Se ha desarrollado una nueva versin de canalizadores de freno y aire. La nueva versin
incluye dos piezas, una rgida similar a la actual, y una flexible que permite absorber parte
de los g olpes q ue se pueda n producir durante el tra nscurso d e las carreras.
As, las pieza s finales s on:
ANTIGUO NUEVOReferencia DENOMINACIN Q. Referencia DENOMINACIN Q.
V4P L615013A CJTO. CANALIZADOR FRENO IZQ. 1V4P L615013 CJTO. CANALIZADOR FRENO IZQ. 1
V4P L615005 FUELLE CANALIZADOR FRENOS 1
V4P L615014A CJTO. CANALIZADOR FRENO DER. 1V4P L615014 CJTO. CANALIZADOR FRENO DER. 1
V4P L615005 FUELLE CANALIZADOR FRENOS 1
V4P L615019A CJTO. CANALIZADOR RADIADOR IZQ. 1V4P L615019 CJTO. CANALIZADOR RADIADOR IZQ. 1
V4P L615010 FUELLE CANALIZADOR FRENOS 1
V4P L615020A CJTO. CANALIZADOR RADIADOR IZQ. 1V4P L615020 CJTO. CANALIZADOR RADIADOR DER. 1
V4P L615010 FUELLE CANALIZADOR FRENOS 1
La s referencia s a ntigua s son sustituida s por dos referencia s pa ra ca da cana lizador.
De momento nica mente est n disponibles la s referencia s de los ca nalizadores de frenos.
15/07/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
56/66
Len Supercopa MK2
Nota tcnica InformativaTechnical Information Note
Brake and Radiador Air inta kes
SEATSport ha s developed a new version of brake and Radia tor a ir intakes . This new version
includes two pa rts, one rigid s imila r to the current one, a nd a flexible one tha t a llows to
absorb some of the hits during the races.
For this reason, the new pa rts a re the following:
OLD NEWReference Denomina tion Q. Reference Denominat ion Q.
V4PL615013A BRAKE AIR INTAKE LEFT 1V4PL615013 BRAKE AIR INTAKE LEFT 1
V4PL615005 BRAKE AIR INTAKE BELLOW 1
V4PL615014A BRAKE AIR INTAKE RIGHT 1V4PL615014 BRAKE AIR INTAKE RIGHT 1
V4PL615005 BRAKE AIR INTAKE BELLOW 1
V4PL615019A RADIATOR AIR INTAKE LEFT 1V4PL615019 RADIATOR AIR INTAKE LEFT 1
V4PL615010 RADIATOR AIR INTAKE BELLOW 1
V4PL615020A RADIATOR AIR INTAKE RIGHT 1V4PL615020 RADIATOR AIR INTAKE RIGHT 1
V4PL615010 RADIATOR AIR INTAKE BELLOW 1
All the old references a re subst ituted by these 2 news references for ea ch a ir intake.
For the moment, the only references a vailab le are the brake air intakes .
15/07/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
57/66
Len Supercopa MK2
Nota tcnica Informativa
Technical Information Note
Modificaciones Len Supercopa MK2
A continuacin se describen las actualizaciones realizadas sobre el Len Supercopa
MK2 2008 para la temporada 2009. En dos grupos, se detallan las piezas de uso
obligatorio y las opcionales.
De uso obligatorio para participar en la Eurocopa SEAT Len:
Descripcin Referencia Cantidad
Polea para correa V4PL145255 1
Radiador servo-direccin* V4PL422885 1
Pastillas de freno anterior Ferodo*** V4PL615115B 1
Pastilla de freno posterior Ferodo*** V4PL615415A 1
De uso opcional como set up del coche:
Descripcin Referencia Cantidad
Barra estabilizadora 20% mas dura** V4PL511407B 1
Muelle de 100 Nm** VN0020065600 2
* Ver pdf instrucciones de montage de SEAT Sport.
** Aprobado en la Ficha Tcnica Leon Supercopa MK2 en VO.
*** Disponibles en el Catalogo Supercopa MK2 2009 SOLO EUROCUP.
06/02/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
58/66
Len Supercopa MK2
Nota tcnica Informativa
Technical Information Note
Technical improvements from Len Supercopa MK2
Following are detailed the improvements done on the SEAT Len Supercopa MK22008 for the season 2009. In two groups are detailed the compulsory parts and the
optional ones.
Compulsory use from Eurocopa SEAT Len:
Descripcin Referencia Cantidad
Steering Wheel puley V4PL145255 1
Radiator from steering Wheel* V4PL422885 1
Front brake pads Ferodo*** V4PL615115B 1
Rear brake pads Ferodo*** V4PL615415A 1
Optional for car set up:
Descripcin Referencia Cantidad
Anti roll bar 20 harder** V4PL511407B 1
Spring 100 Nm** VN0020065600 2
* Se mounting instructions pdf from SEAT Sport.** Technical Form from Leon Supercopa MK2 approved in VO.
*** Available on the Parts Catalogue Len Supercopa MK2 2009 EUROCUP ONLY.
06/02/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
59/66
-
8/10/2019 Notas Tcnicas Len Supercopa
60/66
Len Supercopa MK2
NOTA TCNICA
PROCEDIMIENTO COMPROBACION PRECARGA DIFERENCIALAUTOBLOCANTE
A continuacin informamos del procedimiento para la comprobacin de los valores deprecarga del diferencial autoblocante del cambio de velocidades DSG del LenSupercopa Mk2.
1) Las comprobaciones pueden hacerse tanto en fro como en caliente.2) Colocar el vehiculo sobre airjacks y colocar sus seguros.3) Asegurarse que el motor ha sido parado por el procedimiento correcto, de lo
contrario podra falsearse el valor. El procedimiento, por orden, es el siguientea. Motor en marcha (solo un momento para asegurar Neutral).
b. El display del modulo de volante indica N (neutral)c. Interruptor de contacto off.d. Interruptor de batera off..
4) Fijar una de las ruedas delanteras, (se puede hacer a mano), colocar una llavedinamomtrica de aguja en el tornillo del palier (centro de rueda) de la ruedacontraria y girar en sentido horario fijndose en el par de arrastre. Los valoresdeben estar segn la siguiente tabla:
PRECARGA DIFERENCIAL
Frio 120 15% NmNuevo / Revisado*
Caliente 100 15% NmFrio 90 15% Nm
UsadoCaliente 40 15% Nm
* Tambin se considera nuevo cuando se ha revisado y todava no ha rodado.
INFORMACION ADICIONAL: En el montaje de taller el diferencial autoblocante se tara entre 50 y 70 Nm de
precarga. El aumento de precarga medido en la rueda es debido a las precargas delos 4 ejes de este tipo de cambios. Es aconsejable revisar el autoblocante cuanto la precarga disminuye de 20 Nm en
fro y 10 Nm en caliente.
01/06/2010
-
8/10/2019 Notas Tcnicas Len Supercopa
61/66
Len Supercopa MK2
TECHNICAL NOTE
SLIP DIFERENTIAL CHECKING PROCEDURE
See bellow the SEAT Leon MK2 DSG gear box slip differential PRELOAD procedure.
1) Checks can be done in cold or in warm conditions.2) Up the car with the air-jacks and fix it.3) Take care that the car engine was stopped through the correct procedure, if not
the read value could not be true. The procedure order is as following.a. Start the engine to assure that the shift module indicates N neutral.
b. Put the shif module in N neutral.
c.
Switch off the contact switch.d. Switch off the main switch.
4) To fix one of the front wheels (you can do it by hand), put a needledynamometric tool on the drive shaft bolt (wheel center) and turn the tool inclock wise sense to measure the value. The value must be as following:
SLIP DIFFERENTIAL PRELOAD
Cold 120 15% NmNEW / Rebuilded*
Hot 100 15% NmCold 90 15% Nm
Used
Hot 40 15% Nm
* Revised is considered as new if it has never been used.
ADDITIONAL INFORMATION: When the slip differentials are repaired on the workshop the preload value applied
is between 50 and 70 Nm (differential disassembled from the gear box). Thepreload value that you can read on the wheel centre increase because these kind ofgear boxes have 4 axles and this means bigger friction.
It is advisable to check the slip differential when the preload decrease less than 20
Nm in cold and 10 Nm in warm conditions.
01/06/2010
-
8/10/2019 Notas Tcnicas Len Supercopa
62/66
Len Supercopa MK2
NOTA TCNICA
INTERRUPTOR PRINCIPAL EXTERIOR.
Por la situacin del interruptor situado en el exterior del coche, expuesto a humedades yvibraciones, etc., SEAT Sport recomienda revisar el estado del interruptor de corte
principal de corriente exterior.
Sustituir el interruptor (ref: VN0008127200) en los siguientes casos:a) Si cualquiera de los terminales elctricos no estn solidamente fijados a la base.
b) Si el movimiento de la palanca del interruptor no es preciso.c) Si la base de los terminales ofrecen un mal aspecto o un cambio de color. (ver
foto abajo)
__________________________________
FUSIBLE ECU MOTOR:SEAT Sport recomienda sustituirlos dos fusibles de la ECU motor,situados en la consola de fusibles,
por otros nuevos de 15 Amp. Ver
la posicin en el esquema defusibles adjunto.
15/09/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
63/66
Len Supercopa MK2
TECHNICAL NOTE
EXTERNAL MAIN SWITCH
The external main switch is placed in the external side of the car, for this reason isexposed at humidity, vibrations, etc, SEAT Sport recommend to check it periodically.
We recommend to substitute the external main switch (ref: VN0008127200) in thefollowing cases:
a) If any of the pins is not strongly fixed to the base.
b)
If the switch lever is not precise.c) If the pins base dont offer a good aspect or colour (as the picture bellow).
____________________________________
ECU FUSES:SEAT Sport recommendssubstituting the two ECU fuses for
others new 15Amp. See position onthe scheme in the right side.
15/09/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
64/66
Len Supercopa MK2
NOTA TCNICA
RECORTE FRONTEND
Con el fin de evitar en que, caso de impacto se produzcan un pequeo agujero en elmanguito de agua del radiador secundario se recomienda cortar una parte del frontendque sujeta el faro izquierdo. A continuacin mostramos unos dibujos con el recorterecomendado.
1) Punto critico
2) Primera parte a cortar
3) Segunda parte a cortar hasta el interiordel frontend para aumentar la tolerancia entrelas dos piezas.
02/10/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
65/66
Len Supercopa MK2
TECHNICAL NOTE
CUTTING FRONTEND AREA:
With the purpose to avoid any little hole on the secondary cooling system, its allowedto cut a part of the plastic front-end who support the left headlight. Following we shownsome pictures where is indicated the area to be cutted.
1) Critical point
2) First part to cut
2) Second part to be cutted a long thefront-end to increase the tolerance between
both parts.
02/10/2009
-
8/10/2019 Notas Tcnicas Len Supercopa
66/66
Len Supercopa MK2
NOTA TECNICA / TECHNICAL NOTE
TORNILLO MANOTA DEIRECCION LEON SUPERCOPA
STEERING HANDLE BOLT
A continuacin informamos de la actualizacin realizada en el Catalogo de piezas del
Len Supercopa Mk2 2010.
A partir del 1 de Octubre del 2010, los tornillos utilizados en todas las operaciones de
cambio de manota de direccin, tanto en manguetas ya usadas, as como en manguetas
de recambios del Len Supercopa MK2, deben ser montadas con el nuevo tornillo
M8x45 DIN 912., sustituyendo as el anterior tornillo M8x50 DIN 912, 5mm mas largo.
Following we inform about the update done in the Leon Supercopa MK2 2010 parts
catalogue.
From 1st of October 2010, the bolts to fix the steering handle in the used upright as
well as in the new spare parts, must be fixed with the new bolt M8x45 DIN 912,
substituting the previous one M8x50 DIN 912, 5mm longer.
Nueva referencia: Pieza n 7 Pagina 31 en el Catlogo de piezas. (VN0001157639)
New reference: Part n 7 Page 31 in the Parts Catalogue. (VN0001157639)