IPASOLINK200Quick Reference Manual
La presente guía (QRM) tiene como objetivo ayudar a los ingenieros de campo a realizar la
configuración básica para la puesta en operación y entrega del equipo iPasolink 200; POR NINGUN
MOTIVO Y EN NINGUNA FORMA, el presente documento es el reemplazo de un curso de O&M. Para
mayor información se sugiere la consulta del manual del equipo.
La información previa indispensable que debe tener el ingeniero de instalación, entrega y/o
mantenimiento de enlaces iPasolink200 es la siguiente:
Para establecimiento del enlace a nivel de microondas: Channel spacing, Reference Modulation, E1
Mapping, Ethernet Bandwidth, TX RF Frequency, Frame ID, Tx Power control (así como los valores de
potencia finales)
Para la configuración TDM: Cantidad de E1 para habilitar, los demás parámetros son iguales , LOW BER:
1X10-6, HIGH BER: 1X10-3, etc.
Para la configuración Ethernet: ID de VLAN a transportar , cantidad de puertos requeridos y modalidad
de los puertos.
NEC Internal Use Only© NEC Corporation 2007
Page 2
NEC Proprietary and Confidential
IPASOLINK 200
EQUIPAMIENTO
NOTA: NO HAY SWITCH DE ENCENDIDO
FAVOR DE VERIFICAR CUIDADOSAMENTE
EL VOLTAJE (-48V) ANTES DE CONECTAR
EL SUMINISTRO DE ALIMENTACION AL EQUIPO.
NEC Internal Use Only© NEC Corporation 2007
Page 3
NEC Proprietary and Confidential
INTERFACES DEL EQUIPO IPASOLINK200
Conectarse al equipo en el puerto LCT con un cable de red
uno a uno .
NEC Internal Use Only© NEC Corporation 2007
Page 4
NEC Proprietary and Confidential
User Name: Admin
Password: 12345678
Dirección IP automática de la PC
IP del iP200 : 172.17.254.253
ACCESO POR MEDIO DE WEB-BROWSER
NEC Internal Use Only© NEC Corporation 2007
Page 5
NEC Proprietary and Confidential
1 . Equipment Setup, Equipment Configuration , Setup
2. Equipment Name: Nombre del Sitio
3. Modem 1 y 2 : USED (verifique que ambos modem estén en USED)
4.- SW/XPIC GRP1 seleccionado
5 . 1+1 H.S. (Hot Standby)
1
2
34
5
CONFIGURACION DE EQUIPAMIENTO
NEC Internal Use Only© NEC Corporation 2007
Page 6
NEC Proprietary and Confidential
1
2
1. Radio Configuration y Setup 2.-New Setting, Parámetros de enlace
NEC Internal Use Only© NEC Corporation 2007
Page 7
NEC Proprietary and Confidential
4 E1 + Ethernet (151Mbps)
EJEMPLO: 4E1 + ETHERNET / 128QAM @28MHz
NEC Internal Use Only© NEC Corporation 2007
Page 8
NEC Proprietary and Confidential
1. Provisioning, Tx Power Setting y SW GPR1
Tx Power en dBm
AJUSTE DE POTENCIA MTPC
Ejemplo: Tx pwr : 18 dBm
NEC Internal Use Only© NEC Corporation 2007
Page 9
NEC Proprietary and Confidential
1.- Provisioning, Alarm/AIS Setting y AIS Setting
2.- ModifyAIS Setting
NEC Internal Use Only© NEC Corporation 2007
Page 10
NEC Proprietary and Confidential
Ajuste de umbrales de BER
1.- Provisioning, Alarm/AIS Setting, BER Threshold Setting
2.- SW GRP1RECUERDE: L-BER : 1X10-6
H-BER: 1X10-3
NEC Internal Use Only© NEC Corporation 2007
Page 11
NEC Proprietary and Confidential
1.- Provisioning, Equipment Clock, Setting/Synchcronization
2.- Modify
Local: Master
Remoto: Slave
SINCRONIZACION DEL EQUIPO
NEC Internal Use Only© NEC Corporation 2007
Page 12
NEC Proprietary and Confidential
VERIFICACION DE NIVELES DE RX/TX
1.- Metering, Current metering , SW GRP1
High speed, toma la
medición cada 3
segundos, útil
durante los
alineamientos de
sistema. NO
REQUIERE
ALIGMENT MODE .
ESTE EQUIPO NO
LO UTILIZA.
NEC Internal Use Only© NEC Corporation 2007
Page 13
NEC Proprietary and Confidential
CONFIGURACION TDM (E1 y su CROSS CONNECT)
1.- Provisioning, E1/STM-1/Cross Connect Setting , Add
La cross connect debe ir de Main
Board a MODEM (E1-MODEM).
Cross-connect 1 a 1
NEC Internal Use Only© NEC Corporation 2007
Page 14
NEC Proprietary and Confidential
Del puerto 1 al puerto 1
Se debe agregar una a una las cross-connect de los E1
solicitados.
Si un E1 no esta cross connet , no pasará tráfico.
NEC Internal Use Only© NEC Corporation 2007
Page 15
NEC Proprietary and Confidential
USO de CANAL (Ejemplo : 4E1)
1.- Provisioning, E1/STM-1 Cross Connect Setting, E1 port setting
2.- Modify : De acuerdo a la cantidad de E1 solicitados.
Ejemplo :4 E1
Configuración típica
NEC Internal Use Only© NEC Corporation 2007
Page 16
NEC Proprietary and Confidential
1.- Provisioning, ETH Port Setting
Habilitación de puertos 1 al 4
eléctricos, 5 y 6 ópticos
1-4 FE/GbE ; 5-6 GbE
CONFIGURACION ETH (PORT+VLAN)
NEC Internal Use Only© NEC Corporation 2007
Page 17
NEC Proprietary and Confidential
CONFIGURACION DE VLAN
La VLAN 1 es por default del equipo para su enlace a nivel de microondas,
estrictamente pertenece a la VLAN del modem.
NO PUEDE, NI DEBE SER MODIFICADA, sólo se le asigna un nombre,
ejemplo: DMR
Primero se deberán agregar todas las VLAN ID solicitadas por el cliente, la ruta es:
1.- Provisioning, ETH Funtion Setting, VLAN Setting , VLAN List y Add VLAN ID
a
b
c
NEC Internal Use Only© NEC Corporation 2007
Page 18
NEC Proprietary and Confidential
AGREGACION DE VLAN (VLAN LIST)
1.- Provisioning, ETH Funtion Setting, VLAN Setting, VLAN List y Add VLAN ID
a
b
c
d
Se agrega una a una las VLAN
solicitadas por el cliente (ejemplo ):
1000,2000,3000 y 4000
NEC Internal Use Only© NEC Corporation 2007
Page 19
NEC Proprietary and Confidential
LISTA DE VLAN A TRABAJAR EN EL EQUIPO
VLAN DEFAULT (DMR)
VLAN AGREGADAS
NEC Internal Use Only© NEC Corporation 2007
Page 20
NEC Proprietary and Confidential
MODALIDAD DE PUERTOS ETHERNET(ASIGNACION DE VLAN’s A LOS PUERTOS)
Existen tres modalidades, la que se utilizará es TRUNK, y Acces en caso de prueba de
ping (como sugerencia).
NEC Internal Use Only© NEC Corporation 2007
Page 21
NEC Proprietary and Confidential
ASIGNACION DE VLAN AL MODEM(ENVIO DE VLAN POR MICROONDA)
1.- Provisioning, ETH Funtion Setting, VLAN Setting, VLAN Setting y MODEM1 PORT 01
a
b
c
El MODEM1-Port01, es TRUNK por default
Se deben asignar todas las VLAN ID
configuradas en VLAN LIST, para que puedan
ser transportadas por microondas
NEC Internal Use Only© NEC Corporation 2007
Page 22
NEC Proprietary and Confidential
PUERTO ETH TRUNK(Paso de VLAN con etiqueta)
Selección del puerto ethernet, ejemplo Puerto 1
Asignación del tipo de puerto: TRUNK
a
b
c
Seleccionar las VLAN que deben pasar por ese puerto,
Ejemplo: La VLAN 1000 podrá pasar por el puerto 1; y las
VLAN 2000, 3000, y 4000 no pasarán
NEC Internal Use Only© NEC Corporation 2007
Page 23
NEC Proprietary and Confidential
PUERTO ETH ACCESS(Asignación de VLAN ID a frames sin etiqueta)
Selección de Puerto , ejemplo Port04
Asignación del tipo de
puerto: ACCESS
Selecciona la VLAN ID que le pondrá a las tramas que
vienen si etiqueta. Ejemplo: Se asignara la VLAN 4000, a
las tramas que vengan sin etiqueta y son las únicas que
pasaran por el Port04 (ACCESS)
NEC Internal Use Only© NEC Corporation 2007
Page 24
NEC Proprietary and Confidential
FIN DEL DOCUMENTO
Ajuste de fecha y hora
Top Related