8/6/2019 Trabajo RedesII Evidencia Escrita
1/7
TALLER 1CONFIGURACION SWITCH S1
S1>enable
S1#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
S1config)#vlan 10
S1(config-vlan)#name P1
S1(config-vlan)#exit
S1(config)#vlan 30
S1config-vlan)#name P3
S1(config-vlan)#exit
S1(config)#interface fastEthernet 0/5
S1(config-if)#switchport mode trunk
S1(config-if)#exit
S1config)#interface fastEthernet 0/6
S1(config-if)#switchport access vlan 30
S1(config-if)#exit
S1(config)#interface fastEthernet 0/11
S1(config-if)#switchport access vlan 10
S1(config-if)#exit
S1#show vlan brief
VLAN Name Status Ports
---- ------------------------------ --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
8/6/2019 Trabajo RedesII Evidencia Escrita
2/7
Gig1/1,Gig1/2
10 VLAN0010 active
30 VLAN0030 active
1002 fddi-default active
1003 token-ring-default active
1004 fddinet-default active1005 trnet-default active
CONFIGURACION ROUTER R1
R1>enable
R1#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#interface fastethernet 0/1
R1(config-if)#no shutdown
R1(config)#interface fastethernet 0/1.10
R1(config-subif)#encapsulation dot1q 10
R1(config-subif)#ip address 172.17.10.1
% Incomplete command.
R1(config-subif)#ip address 172.17.10.1 255.255.255.0
R1(config-subif)#exit
R1(config)#interface fastethernet 0/1.30
R1(config-subif)#encapsulation dot1q 30
R1(config-subif)#ip address 172.17.30.1 255.255.255.0
R1(config-subif)#exit
R1(config)#exit
8/6/2019 Trabajo RedesII Evidencia Escrita
3/7
TALLER 2Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface fastethernet 0/0
Router(config-if)#ip address 172.16.1.1 255.255.255.0
Router(config-if)#exit
Router(config)#interface serial 2/0
Router(config-if)#ip address 172.16.2.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#show interfaces
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface fastethernet 0/1
%Invalid interface type and number
Router(config)#interface fastethernet 0/0
Router(config-if)#ip address 172.16.5.1 255.255.255.0
Router(config-if)#exit
Router(config)#interface serial 2/0
8/6/2019 Trabajo RedesII Evidencia Escrita
4/7
Router(config-if)#ip address 172.16.4.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#show interfaces
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#router rip
Router(config-router)#ip route 172.16.1.0 255.255.255.0 172.16.2.1
Router(config)#router rip
Router(config-router)#ip route 172.16.5.0 255.255.255.0 172.16.4.2
Router(config)#router rip
Router(config-router)#network 172.16.2.0
Router(config-router)#network 172.16.3.0
Router(config-router)#network 172.16.4.0
Router(config-router)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#show ip route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
8/6/2019 Trabajo RedesII Evidencia Escrita
5/7
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is not set
Router#ping 172.16.2.0
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.2.0, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Router#
Router#
Router#traceroute 172.16.2.0
Type escape sequence to abort.
Tracing the route to 172.16.2.0
1 * * *
2 * * *
3 * * *
4 * * *
5 * * *
6 * * *
7 * * *
8 * * *
9 * * *
10 * * *
11 * * *
12 * * *
13 * * *
8/6/2019 Trabajo RedesII Evidencia Escrita
6/7
14 * * *
15 * * *
16 * * *
17 * * *
18 * * *
19 * * *
20 * * *
21 * * *
22 * * *
23 * * *
24 * * *
25 * * *
26 * * *
27 * * *
28 * * *
29 * * *
30 * * *
Switch>enable
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface fastethernet 0/24
Switch(config-if)#switchport mode trunk
Switch(config-if)#exit
Switch(config)#exit
(aplica para los tres switch)
8/6/2019 Trabajo RedesII Evidencia Escrita
7/7
Top Related