Post on 14-Apr-2018
7/30/2019 CAP 207 Series
1/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
MODEL 200
SERIES PISTONSINGLE ENGINE AIRCRAFT
PROGRAMA
DE AERONAVEGABILIDAD CONTINUADA
CAP
TRAVEL AIR E.I.R.L.
CARATULA
AUTOR: MELQUIADES CHAVEZ GALDOS
FECHA: 08-ABRIL-2010 REVISIN: ORIGINAL PAGINA: 1
7/30/2019 CAP 207 Series
2/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
PROGRAMADE AERONAVEGABILIDAD CONTINUADA
CAP
MANUAL N
REVISION N
ASIGNADO A:
FECHA: 08-ABRIL-2010 REVISIN: ORIGINAL PAGINA: 2
ORIGINAL
7/30/2019 CAP 207 Series
3/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
INDICE GENERAL
LISTA DE CONTENIDO PAGINA
CARTULA DEL MANUAL 1
CARATULA DE ASIGNACION DEL MANUAL 2
INDICE GENERAL 3 al 5
APLICABILIDAD 6
LISTA DE PAGINAS EFECTIVAS 7 al 9
Pgina en blanco 10
A.0.- PROGRAMA DE AERONAVEGABILIDAD CONTINUADA (CAP) 11
A.1 INTRODUCCIN 11
A.2 POLITICA 11
A.3 OBJETIVO 11
A.4 ORGANIGRAMA 12
Pgina en blanco 13
B.0.- CONTROL DEL PROGRAMA DE AERONAVEGABILIDAD CONTINUADA (CAP) 14
B.1 CARATULA DEL PROGRAMA 14
B.2 CARATULA DE ASIGNACION DEL PROGRAMA 14
B.3 NUMERO DE CONTROL Y LISTA DE DISTRIBUCION DEL PROGRAMA 14
B.4 APROBACION Y REVISIN 15
B.5 REGISTRO DE REVISIONES 16
Pgina en blanco 17
INTRODUCCION AL PROGRAMA DE AERONAVEGABILIDAD CONTINUADA 18
1.0 DISCUSION 18
1.1 INTRODUCCION AL CAP 18
1.2 OBJETIVO DEL CAP 18
2.0 (DETALLES IMPORTANTES DEL SISTEMA / ESTRUCTURAL) SSDS 19
2.1 FUNDAMENTOS USADOS PARA SELECCIONAR LOS SSDs 19
2.2 LOS SSDs FUERON SELECCIONADOS BASADOS EN LO SIGUIENTE 19
A. EXPERIENCIA EN EL SERVICIO 19
INDICE GENERAL (Cont....)
FECHA: 08-ABRIL-2010 REVISIN: ORIGINAL PAGINA : 3
7/30/2019 CAP 207 Series
4/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
LISTA DE CONTENIDO PAGINA
B. BOLETINES DE SERVICIO, NEWSLETTERS Y SERVICEKITS 19
C. ANALISIS 19
D. PRUEBAS 20
C. INSPECCION DEL AVION 20
3.0 REPORTE Y COMUNICACIONES 20
3.1 REPORTANDO LAS DISCREPANCIAS 21
3.2 DISPOSICION DEL FORMATO DE DISCREPANCIAS 21
3.3 ACCIONES DE SEGUIMIENTO DEL FABRICANTE 21
4.0 INFORMACION BASICA 22
4.1 INSPECCION 22
1. GENERAL 22
2. MATERIALS AND EQUIPMENT 22
3. PROCEDURES 23
A. Surface Cleaning 23
B. Applicantion of Penetrant 23
C. Removal of Excess Penetrant 23
D. Application of Developer 23
E. Interpretation of Indication 24
4.2 MANUALS 24
4.3 SERVICE LETTERS/BULLETINS 24
5.0 APPLICABILITY/LIMITATIONS 24
6.0 SIGNIFICANT DETAILS 25
6.1 CAP FORMS 25
6.2 REPAIR INFORMATION/MODIFICATION 25
DISCREPANCE REPORT 26
SECTION I TECHNICAL DOCUMENT REFERENCE 27
SERVICE MANUALS 27
SERVICE BULLETIN 27
Pgina en blanco 28
SECTION II - LISTING OF CONTINUED AIRWORTHINESS PROGRAM INSPECTIONS 29
INDICE GENERAL (Cont....)
LISTA DE CONTENIDO PAGINA
FECHA: 08-ABRIL-2010 REVISIN: ORIGINAL PAGINA : 4
7/30/2019 CAP 207 Series
5/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
SECTION III CONTINUING AIRWORTHINESS PROGRAM INSPECTION 30
27-30-02 Elevator Trailing Edge andTrim Tab Inspections 30-31
28-30-01 Quick Drain Valves Fuel Reservoir and Fuel Tanks 32-3328-40-01 Fuel Gaging Systems 34
29-10-01 Hydraulic Hose Replacement and Hydraulic Component Replacement 35-36
32-50-02 Nose Gear Steering Collar and Upper Torque Link 37-39
39-00-01 Engine Compartment Wiring and Equipment Installation 40
53-40-01 Fuselage Wing Strut Attach Forging 41-42
53-40-02 Fuselage Wing Attachments 43-44
53-40-04 Fuselage Vertical Fin Attachments 45-49
53-40-06 Main Landing Gear Support Fittings 50-51
55-10-01 Horizontal Stabilizer Aft Attach Bracket 52-53
55-30-01 Vertical Tail Fin Fuselage Attachments 54-59
57-10-03 Front Spar Splice LH Aft 60-61
57-10-04 Front Spar Splice LH Aft 62-63
57-10-06 Wing Fuselage Attach Fittings 64-65
57-10-11 Wing Strut Tube 66
Pgina en blanco 67
FECHA: 08-ABRIL-2010 REVISIN: ORIGINAL PAGINA : 5
7/30/2019 CAP 207 Series
6/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
APLICABILIDAD
MODEL YEAR SERIAL
207/T207 1969 THRU 1984 20700001 THRU 20700788
OB-1001 AO DE FABRICACION 1969 SERIAL NUMBER 20700055
OB-1888 AO DE FABRICACION 1974 SERIAL NUMBER 20700266
FECHA: 08-ABRIL-2010 REVISIN: ORIGINAL PAGINA : 6
7/30/2019 CAP 207 Series
7/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
LISTA DE PGINAS EFECTIVAS
PAGINA REVISION FECHA
1 ORIGINAL 08-ABR-2010
2 ORIGINAL 08-ABR-2010
3 ORIGINAL 08-ABR-2010
4 ORIGINAL 08-ABR-2010
5 ORIGINAL 08-ABR-2010
6 ORIGINAL 08-ABR-2010
7 ORIGINAL 08-ABR-2010
8 ORIGINAL 08-ABR-2010
9 ORIGINAL 08-ABR-2010
10 ORIGINAL 08-ABR-2010
11 ORIGINAL 08-ABR-2010
12 ORIGINAL 08-ABR-2010
13 ORIGINAL 08-ABR-2010
14 ORIGINAL 08-ABR-201015 ORIGINAL 08-ABR-2010
16 ORIGINAL 08-ABR-2010
17 ORIGINAL 08-ABR-2010
18 ORIGINAL 08-ABR-2010
19 ORIGINAL 08-ABR-2010
20 ORIGINAL 08-ABR-2010
21 ORIGINAL 08-ABR-2010
22 ORIGINAL 08-ABR-2010
23 ORIGINAL 08-ABR-2010
24 ORIGINAL 08-ABR-2010
25 ORIGINAL 08-ABR-2010
26 ORIGINAL 08-ABR-2010
27 ORIGINAL 08-ABR-2010
FECHA: 08-ABRIL-2010 REVISIN: ORIGINAL PAGINA : 7
D
ire
c
c
i
n
G
e
n
e
ra
l
d
e
A
e
ro
n
u
tic
a
C
iv
il
7/30/2019 CAP 207 Series
8/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
LISTA DE PGINAS EFECTIVAS (Cont)
PAGINA REVISION FECHA
28 ORIGINAL 08-ABR-2010
29 ORIGINAL 08-ABR-2010
30 ORIGINAL 08-ABR-2010
31 ORIGINAL 08-ABR-2010
32 ORIGINAL 08-ABR-2010
33 ORIGINAL 08-ABR-2010
34 ORIGINAL 08-ABR-2010
35 ORIGINAL 08-ABR-2010
36 ORIGINAL 08-ABR-2010
37 ORIGINAL 08-ABR-2010
38 ORIGINAL 08-ABR-2010
39 ORIGINAL 08-ABR-2010
40 ORIGINAL 08-ABR-2010
41 ORIGINAL 08-ABR-2010
42 ORIGINAL 08-ABR-2010
43 ORIGINAL 08-ABR-2010
44 ORIGINAL 08-ABR-2010
45 ORIGINAL 08-ABR-2010
46 ORIGINAL 08-ABR-2010
47 ORIGINAL 08-ABR-2010
48 ORIGINAL 08-ABR-2010
49 ORIGINAL 08-ABR-2010
50 ORIGINAL 08-ABR-2010
51 ORIGINAL 08-ABR-2010
52 ORIGINAL 08-ABR-2010
53 ORIGINAL 08-ABR-2010
54 ORIGINAL 08-ABR-2010
55 ORIGINAL 08-ABR-2010
FECHA: 08-ABRIL-2010 REVISIN: ORIGINAL PAGINA : 8
D
ire
c
c
i
n
G
e
n
e
ra
l
d
e
A
e
ro
n
u
tic
a
C
iv
il
7/30/2019 CAP 207 Series
9/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
LISTA DE PGINAS EFECTIVAS (Cont)
PAGINA REVISION FECHA
56 ORIGINAL 08-ABR-2010
57 ORIGINAL 08-ABR-2010
58 ORIGINAL 08-ABR-2010
59 ORIGINAL 08-ABR-2010
60 ORIGINAL 08-ABR-2010
61 ORIGINAL 08-ABR-2010
62 ORIGINAL 08-ABR-2010
63 ORIGINAL 08-ABR-2010
64 ORIGINAL 08-ABR-2010
65 ORIGINAL 08-ABR-2010
66 ORIGINAL 08-ABR-2010
67 ORIGINAL 08-ABR-2010
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 9
D i r e c c i n G e n e r a l d e A e r o n u t i c a C i v i l
7/30/2019 CAP 207 Series
10/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
PAGINA INTENCIONALMENTE
DEJADO EN BLANCO
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 10
7/30/2019 CAP 207 Series
11/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
A.0 PROGRAMA DE AERONAVEGABILIDAD CONTINUADA (CAP)
A.1 INTRODUCCIN
El presente Programa de Aeronavegabilidad Continuada ha sido desarrollado porTRAVEL AIR E.I.R.L. en base al Manual D5121-1-13 publicado por Cessna AircraftCompany, como un complemento al Programa de Mantenimiento Aprobado por laDGAC.
Este Manual ser usado por TRAVEL AIR como parte de su Programa deMantenimiento, para garantizar la Aeronavegabilidad continuada de sus Aeronaves. losICA (Inspecciones de aeronavegabilidad Continuada) son fichas de inspeccin dondese muestran los cumplimientos INICIAL y REPETITIVO .
A.2 POLITICA
TRAVEL AIR E.I.R.L., posee un equipo de trabajo de alto nivel profesional cuyasacciones diarias de mantenimiento las ejecutamos con un elevado profesionalismopara garantizar la aeronavegabilidad continua de nuestras aeronaves, nuestra visin deempresa est basada en los siguientes principios:
INTEGRIDAD PERSONAL como expresin de disciplina, orden, respeto,honestidad y entusiasmo.
CREATIVIDAD E INNOVACIN como parte de nuestro reto diario para elmejoramiento contino.
PRODUCTIVIDAD en nuestro trabajo y en el empleo de los recursos materiales.
CONSCIENCIA en la ejecucin de tareas de mantenimiento libre de errores y el
COMPROMISO leal con la compaa y con las realizaciones de calidad.
SEGURIDAD EN LAS OPERACIONES: Actitud proactiva y acciones dinmicaspreservando la seguridad e integridad de las aeronaves.
A.3 OBJETIVO.
El objetivo de este Programa de Aeronavegabilidad Continuada es garantizar laaeronavegabilidad de cada una de nuestras aeronaves para brindan un servicioms eficiente con un alto grado de seguridad para nuestros clientes.
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 11
7/30/2019 CAP 207 Series
12/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
A.4 ORGANIGRAMA
Este organigrama obedece nicamente a los responsables directos de velar elcumplimiento del Programa de Aeronavegabilidad Continua (CAP).
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 12
GERENTE DE MANTENIMIENTO
JEFE DE CONTROL DE
CALIDAD
INSPECTOR DE
MANTENIMIENTO
ICA
CONTROL DE
MANTENIMIENTO
INSPECTOR DE
MANTENIMIENTO
NAZCA
SUPERVISOR DE
MANTENIMIENTO
ICA
SUPERVISOR DE
MANTENIMIENTO
NAZCA
7/30/2019 CAP 207 Series
13/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
PAGINA INTENCIONALMENTE
DEJADO EN BLANCO
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 13
7/30/2019 CAP 207 Series
14/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
B.0 CONTROL DEL PROGRAMA DE AERONAVEGABILIDAD CONTINUADA (CAP)
B.1 CARATULA DEL PROGRAMA
Es la primera pgina de este Programa con el propsito de facilitar su identificacin.
B.2 CARATULA DE ASIGNACION DEL PROGRAMA
Es la Segunda Pagina de este Programa donde se registra el Numero del Manualasignado, el Nmero de Revisin actual y el nombre del departamento, entidad o aquien es asignado el presente el manual.
B.3 NUMERO DE CONTROL Y LISTA DE DISTRIBUCION DEL PROGRAMA
Los Programa asignados sern numerados correlativamente con un nmero decontrol. El departamento de Control de Mantenimiento mantendr una Lista deAsignacin de los Manuales en la que incluir el nmero de control y las revisiones quese han incorporado.
01 Direccin General de Aeronutica Civil (D.G.A.C.) (CD)
02 Gerencia de Mantenimiento
03 Departamento de Control de Calidad
04 Control de Mantenimiento
05 Estacin de Lnea Nazca
06 Departamento de Instruccin y Publicaciones
B.4 APROBACION Y REVISIN
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 14
7/30/2019 CAP 207 Series
15/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
En esta seccin se establecen los procedimientos para que el CAP (Programa deAeronavegabilidad Continuada) se mantenga actualizado.
La revisin del CAP, es responsabilidad directa del Gerente de Mantenimiento, sin
embargo podr delegar esta funcin; toda vez que la DGAC emita una nueva Normatcnica, revisiones efectuadas por Cessna o cuando Travel Air considere convenientepara mejorar su Programa.
El responsable de efectuar la revisin recibir todas las sugerencias de revisiones almanual de los usuarios asignados, insertando las correcciones o modificaciones queconsidere necesarias; una vez realizada la revisin se insertara al el pie de pgina lafecha de la revisin seguido del N de revisin correspondiente, para posteriormentesolicitar a travs del Inspector Principal de Mantenimiento (IPM DGAC) su aceptacino aprobacin.
El responsable de la revisin remitir al IPM de Travel Air, a travs de mesa de partesdel MTC, una carta de presentacin con el logo tipo de la compaa y la firma delGerente de Mantenimiento junto con un ejemplar de las pginas revisadas y dos copiasde la lista de pginas efectivas.
Una vez aprobada o aceptada la revisin, con la refrenda del IPM en la lista de laspginas efectivas, el Departamento de Control de Mantenimiento sacar copiassuficientes de las revisiones para su distribucin a las diferentes reas.
Las revisiones sern distribuidas por el encargado del Departamento de Control deMantenimiento con un cargo de entrega, ser responsabilidad del usuario el insertar lasrevisiones de acuerdo con la lista de pginas efectivas.
B.5 REGISTRO DE REVISIONES
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 15
7/30/2019 CAP 207 Series
16/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
REVISIONFECHA DEREVISION
FECHA DEAPROBACION
PREPARADO POR
ORIGINAL 08-05-2010 CARLOS PALACIN CORCUERA
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 16
7/30/2019 CAP 207 Series
17/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
PAGINA INTENCIONALMENTE
DEJADO EN BLANCO
INTRODUCCION AL PROGRAMA DE AERONAVEGABILIDAD CONTINUADA
1.0 DISCUSION.
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 17
7/30/2019 CAP 207 Series
18/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
El programa de la aeronavegabilidad Continuada (CAP) consiste en recomendaciones deinspeccin, que cuando se combinan con los requisitos de mantenimiento existentes,ayudar a mantener la aeronavegabilidad continuada de la aeronave.
1.1 INTRODUCCION AL CAP.
Las aeronaves contenidas en este CAP, fueron entregados (cuando fueron vendidos) conlos programas de inspeccin recomendadas. Manuales de mantenimiento actualizadoscontinuamente, complementados con los boletines del servicio e informacin para elpropietario fueron proporcionados (mediante subscripciones con Cessna) con la intencinde mantener la aeronavegabilidad de las aeronaves.
Debido a que estas aeronaves han sido asignados a variadas misiones (vuelos privados,tursticos, paracaidismo etc.), el tipo de cuidado que se le presta, as como elenvejecimiento general e ndice de uso (horas de vuelo del avin) , Cessna consideranecesario proporcionar requerimientos adicionales a los programas de inspeccin como un
medio de garanta adicional para que los aviones puedan continuar siendo aeronavegables.De la experiencia que Cessna ha adquirido y el apoyo continuo de los reportes de campode las aeronaves, Cessna contina dando informacin de servicio para las aeronaves pormedio de los CAP.
Este CAP ha sido desarrollado por Cessna en conformidad con las directrices que figuranen el CAP GAMA Formato Spec # 7.
El CAP no intenta hacer cambios o sustituir, pero puede proporcionar informacin adicionalal MANUAL DE MANTENIMIENTO, boletines de servicio o cartas de servicio que sonaplicables.
1.2 OBJETIVO DEL CAP.Este CAP se ha desarrollado para asegurar la capacidad de la aeronave para performardentro de los parmetros de la certificacin original.
Los CAP estn direccionados hacia los componentes estructurales primarioy secundario, motor, Items elctricos y sistemas primario y secundariopara lograr este objetivo declarado de aeronavegabilidad continuada.
Condiciones para establecer las bases para que los Itemsdetallados en los CAP sean incluidos, la aeronave debe
reunir con las siguientes condiciones:A. La aeronave ha sido mantenida en concordancia con las recomendaciones de Cessna
o equivalente.
B. Cuando el CAP est dirigido a un componente o parte especfico, se da a entender quela inspeccin incluir la observacin y evaluacin de las areas alrededor de las partes yequipamientos. Cualquier discrepancia encontrada durante la inspeccin fuera delalcance del CAP deber ser comunicado a Cessna a travs del sistema de reporte decondicin existente de manera que se pueden realizar cambios al CAP en casonecesario.
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 18
7/30/2019 CAP 207 Series
19/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
C. Los aviones modificados por un Certificado Tipo Suplementario (STC) no sonresponsabilidad de Cessna. Cualquier inspeccin requerida dentro de lo manuales de
Cessna o CAPs que tengan reas que hayan sido modificados por un STC sernautomticamente referidas al titular del STC, por el propietario y / u organizacin demantenimiento para la obtencin de las directrices de mantenimiento aprobadas por laFAA.
2.0 (DETALLES IMPORTANTES DEL SISTEMA / ESTRUCTURAL) SSD'S.
Los elementos designados para la inspeccin en este documento son esas estructuras osistemas que incluyen el motor y elctricos cuyos fallas podran causar la prdida o daossustanciales a la aeronave. Los trminos detalles estructuralmente importantes odetalles importantes del sistema (SSD) se aplicar a estos Items crticos. La seleccin yel seguimiento de estos SSDs es el ncleo del (CAP) Programa de Aeronavegabilidad
continuada.
2.1 FUNDAMENTOS USADOS PARA SELECCIONAR LOS SSD'S.
La flota Cessna series 200 fue diseada para vuelos comerciales y vuelos de placer. Sinembargo, desde su produccin en comn algunos de estos aviones tienen ms de 10.000horas de vuelo y otros son mayores de (20 aos) con pocas horas de vuelo, los mtodos yfundamentos utilizados para la seleccin de los SSD crticos se dispone en el prrafo 2-2,A. hasta la E.
2.2 LOS SSD'S FUERON SELECIONADOS BASADOS EN LO SIGUIENTE:
A. EXPERIENCIA EN EL SERVICIO.
La correspondencia del cliente y reportes de condicin tambin fueron revisadosdurante el proceso de seleccin de los SSDs crticos. Los informes (reportes) tambinfueron utilizados para seleccionar los items que eran similares en aplicacin para otrasaeronaves basadas en funcin a su diseo y carga.
B. BOLETINES DE SERVICIO, NEWSLETTERS, Y SERVICE KITS.
Los boletines de servicio han sido revisados y volvieron a tratarse los criterios deseguridad de vuelo para ayudar a seleccionar los SSD crticos. Algunos de estosdocumentos se consideran vitales para la operacin segura de la aeronave y en
consecuencia, la estructura afectada o componentes del sistema sern enumeradoscomo un SSD.
NOTA.Algunos de estos boletines pueden ya estar
incorporados dentro del programa demantenimiento del operador.
C. ANALISIS.
Se revisaron los anlisis existentes para identificar los componentes en
reas que puedan haber mostrado el potencial requerimiento deinspeccin adicional.
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 19
7/30/2019 CAP 207 Series
20/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
D. PRUEBAS.
Se realizo una revisin de los resultados de las pruebas aplicables al diseo. Seevaluaron los resultados de las condiciones de carga junto con pruebas estticas y defatiga. Los datos resultantes se utilizaron para determinar si el componente debera serconsiderado como un SSD para su incorporacin dentro del CAP.
E. INSPECCION DEL AVION.
Aeronaves con muchos aos de operacin fueron desarmadas completamente para serinspeccionado con la finalidad de seleccionar los SSD. Inspecciones especiales
fueron realizadas a otras aeronaves con muchos aos de operacin paracomplementar estas inspecciones.
Los efectos de la corrosin no se han tenido en cuenta en la seleccin y justificacindel SSD o los efectos sobre la fatiga por estrs. Es difcil determinar los efectos de lacorrosin, pero como son recibidos los reportes de inspeccin del CAP, los tiemposde inspeccin sern ajustados como sea necesario dependiendo de la severidad de ladiscrepancia.
NOTA
Si una aeronave tiene un historial donde se hayan realizado vuelos dereconocimiento a baja altura sobre el terreno las inspecciones Inicial y Repetitivo
se reducen a la mitad.
3-0. REPORTE Y COMUNICACIONES.
Para que los CAP puedan tener xito en forma permanente, es esencial que exista un libreflujo de informacin entre el operador, la DGAC y Cessna. Los detalles significativos delos resultados de la inspeccin, reparaciones y modificaciones ejecutados deben sercomunicados a Cessna con el fin de evaluar la eficacia de sus procedimientos de controlrecomendadas y los intervalos de tiempo. En algunos casos, es posible obtener
extensiones en las frecuencias de inspeccin si la informacin obtenida sugiere la aparicinde problemas de fatiga a un mayor nmero de horas de vuelo de lo inicialmente previsto.
Adems, Items no considerados anteriormente para su inclusin en el CAP pueden serdescubiertos por el operador a travs de las inspecciones y los reportes de inspeccin.Estos Items sern evaluados por Cessna y si es de aplicacin general a las configuracionesde la aeronave en cuestin, se aadir al CAP para el beneficio de todos.
Se ha establecido e incorporado en este documento un sistema de reporte consecuente con lossistemas empleados por el CESSNA PROPELLER PRODUCT SUPPORT ORGANIZATION yregistrada en este CAP. Las copias de los formularios pertinentes estn disponibles para usted en laEstacin de Servicio de Cessna o el Servicio de Ingeniera de campo de la Fbrica.
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 20
7/30/2019 CAP 207 Series
21/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
3.1. REPORTANDO LAS DISCEPANCIAS.
El reporte de las discrepancias es esencial para proveer y ajustar los parmetros de inspecciny los intervalos de tiempo en mayor o menor intensidad, as como la incorporacin o eliminacin delos SSD. Basado en los datos reportados, puede ser posible perfeccionar los mtodos de inspeccin,reparaciones y modificaciones involucrados en los SSD.Todas las rajaduras y corrosiones de gravedad encontrados en materia de inspeccin de un SSDsern notificadas a la Cesnna. Los resultados de la inspeccin SSD se informara en un formulariocomo se muestra en la pgina siguiente:
3.2. DISPOSICION DEL FORMATO DE DISCREPANCIAS.
Enviar todos los datos disponibles incluyendo las reparaciones, fotos, etc. a la siguientedireccin:
Cessna Aircraft CompanyAttn: CAP Program
Technical Support ServicesDept. 751
P.O. Box 7706Wichita, Kansas 67277
Fax 1-316-942-9006
NOTA
Este sistema no reemplaza la condicin de comunicacin del sistema dereportes para aquellos Items no cubiertos por el CAP .
3.3. ACCIONES DE SEGUIMIENTO DEL FABRICANTE.
Todos los reportes SSD sern revisados para ver si algunas de las siguientes acciones deberanser tomadas:
1. Chequear sus efectos en la integridad estructural u operacional.
2. Chequear otras aeronaves con altas cantidad de horas a fin de considerar laemisin de un boletn de Servicio.
3. Ver si un reforzamiento es necesario.
4. Revisar el CAP si es necesario.
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 21
7/30/2019 CAP 207 Series
22/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
4.0. INFORMACION BASICA.
Este CAP aplica a los aviones Series 200. Refirase a los manuales deServicio/Mantenimiento individuales de la serie 200 para los especficos programas deinspeccin de su aeronave.
NOTA.- Desde el prrafo 4.1 hasta la pgina final se mantendrn tal como fueronpublicados en Ingles.
4.1. INSPECTION.
1. GENERAL
A. A recommended method of inspection is given; however, if the operator can show
that an alternate method is equal to or better than the suggested method fordetecting damage, then it will be considered as a possible alternate inspectionmethod.
B. The following general eddy current inspection shall be used where called out as"INSPECTION PROCEDURES" within Section III.
C. Eddy current inspect using an eddy current test instrument capable of detecting thesimulated cracks in a bolt hole and surface reference standard equivalent to theHRS-10A and SRS-123A standard available from NDT Engineering, 7056 S. 220th,Kent, WA 98032.
D. The following general liquid penetrant inspection shall be used where called out as
"INSPECTION PROCEDURES" within Section III.
E. Penetrant inspection is used to detect small cracks or discontinuities open to thesurface which may not be evident by normal visual inspection. Penetrant inspectioncan be used on most airframe parts and assemblies accessible for its application.The inspection is performed by applying a liquid which penetrates into surfacedefects so that visual indications are obtained by color contrast or fluorescence ofthe penetrant under the display of black light. The penetrant method of inspectionrequires that the surface in the inspection area be thoroughly clean and free ofpaint.
2. MATERIALS AND EQUIPMENT
A. Due to the high sensitivity and the ability to detect fatigue cracks open to thesurface, portable fluorescent penetrant system is required as the inspection methodwhen specified for penetrant inspection of specific areas of the airframe structure.
B. The following penetrant materials are used to make a complete self-containedfluorescent penetrant kit. There are several manufacturers of fluorescent penetrantmaterials which are satisfactory, provide the materials are used as a family groupand meet the requirements of QPL-25135. A family is a series of items required toperform a specific method or process of penetrant inspection which is furnished byone manufacturer and meet the requirements of QPL-25135.
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 22
7/30/2019 CAP 207 Series
23/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Equipment Manufacturer
ZA 43 Fluorescent Penetrant Kit Magnaflux Corporationcontains the following: 7300 W. LawrenceAvenue Chicago, IL
60656ZL-22A PenetrantZP-9B Nonaqueous DeveloperZP4 Dry Power DeveloperSKC-7 CleanerZB-32A Portable Black Light
3. PROCEDURES
A.Surface Cleaning
(1) The area to be inspected must be free from any dirt, grease, oil, paint or anycontaminants which would mask or close a defect open to the surface. Thesurface should be dry before applying the penetrant.
CAUTION: DO NOT USE TRICHLORETHYLENE AS A CLEANING AGENT ONTITANIUM OR HIGH NICKEL ALLOY MATERIALS.
(2) The penetrant materials and the area to be tested shall have a temperature of60F to 130F
B. Application Of Penetrant.(1) Completely cover the area of inspection with penetrant by brushing. Allow
penetrant to remain on the area for a minimum of 30 minutes. After 35 minutes,reapply using a scrubbing action. This will help in the removal of the penetrantfrom the surface by loosening the previously applied partially dried penetrant.
C. Removal Of Excess Penetrant.
(1) Remove excess penetrant from surface by wiping with a clean dry lint-free cloth.Remove remaining penetrant with a clean lint-free cloth, dampened with penetrantcleaner. Do not flush surface with penetrant cleaner as this will flush penetrantfrom defects. Examine inspection area under the black light to ensure removal of
all surface penetrant.
D. Application Of Developer.
(1) The essential step in applying developer is to get the minimum thicknesspossible..The best results are obtained by a very thin coating. The Film ofdeveloper should be slightly translucent. When applying dry power developer,thoroughly dust area, then blow off excess power. When applying nonaqueouswet developer from a pressurized can, spray a thin coat on the surface and allowto dry in ambient air. The developer liquid shall be agitated frequently to preventsettling of the solid particles in the liquid vehicle. The full dwell time afterdeveloper has been applied should be no less than 5 minutes.
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 23
7/30/2019 CAP 207 Series
24/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
E. Interpretation of Indications.
(1) An 8X magnifying glass should be used to examine area unless indications arevisible to the naked eye. Any surface break will be revealed by fluorescentindication on a blueish background. A fluorescent line will indicate a crack and willbe sharply defined at first and the amount of bleeding gives a clue to the depth ofthe crack. Inspectors should watch indications grow, since the first sharpindications tell much of the nature of the defect, and the amount of bleeding givesinformation as to the extent. A deep discontinuity indication will reappear anumber of times when wiped clean and developer reapplied.
4.2. MANUALS.
Cessna has a number of documents that are useful to maintaining continuedairworthiness of aircraft:
Cessna 200 Series Service ManualCessna 200 Series Parts CatalogsCessna Single Engine Service Bulletin SummariesCessna Newsletter Summaries
For information regarding these documents, contact:
Cessna Aircraft Company Supply DivisionAttn: SPA DepartmentP.O. Box 949Wichita, Kansas 67201Fax 1-316-68-84187
4.3. SERVICE LETTERS/BULLETINS.
As an aid to the operator, a listing of all the Service Letters/Bulletins pertaining tothese 200 Series Aircraft CAPS, are listed in Section 1, titled: TECHNICALDOCUMENT REFERENCE. For information concerning the technical data included inthese Service Letters/Bulletins that apply to your aircraft, you may contact Cessna'sPropeller Technical Information Services, Department 753. The telephone number forcustomer assistance is (316) 941-7550/Fax 1-316-942-9006. A Service Bulletin Listing
Program, that provides a list of all Cessna Service Bulletins and Service Newsletters,applicable to a particular airplane model and serial number is also available fromCessna. This service is obtained by calling (316) 941-6118/Fax 1-316-342-9006.
5.0. APPLICABILITY/LIMITATIONS.
The Cessna 200 series aircraft have had many modifications that were accomplishedunder STC's by other organizations without Cessna Engineering involvement.Because Cessna does not have knowledge of the airworthiness of STC's, this reportcannot apply to those areas affected by such STC's and the STC holder shouldprepare a CAP for each particular modification.
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 24
7/30/2019 CAP 207 Series
25/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
6.0. SIGNIFICANT DETAILS.
This section contains the significant details selected by the rationale process describedin paragraph 2-2. These items are considered significant to maintain continuedairworthiness of all Cessna 200 series models. Service Bulletins considered mandatoryfor airworthiness will be listed in Section 1, TECHNICAL DOCUMENT REFERENCE.
A summary of the CAPs is shown in the section titled: LISTING OF CONTINUEDAIRWORTHINESS INSPECTIONS. This can be used as a checklist by the operators.
6.1. CAP FORMS.
Each CAP will be listed on a form and will contain the following:
1. Continued Airworthiness Inspection Number.2. Title.3. Effectivity.4. Inspection Compliance.5. Initial.6. Repeat.7. Purpose.8. Inspection Procedure.9. Access/Location.10. Detectable Crack Size.11. Inspection Procedure.12. Repair/Modification.13. Comments.
6.2. REPAIR INFORMATION/MODIFICATION
Repairs may be made in accordance with the applicable Cessna Service/MaintenanceManual or FAA AC43-13 acceptable methods of alteration and repair. Any repair notcovered by the recommendations in this CAP Program may be coordinated with CessnaTechnical Information Services at Telephone (316) 941-8500/Fax (316) 942-6000
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 25
7/30/2019 CAP 207 Series
26/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
CESSNA AIRCRAFT COMPAINYMODEL 200 SERIES
CONTINUED AIRWORTHINESS PROGRAM
DISCREPANCY REPORT
CAP'S NO: _______________AIRPLANE LOCATION: _________________S/N OF
AIRPLANE:_________
INSPECTION CONDUCTED: Date ___________Airplane Total Hours ______________ Cycles N/A
Component Total Hours____________ Cycles N/A
SERVICE HISTORY:
____________________________________________________________________________________
________________________________________________________________________________________________________________________________________________________________________
INSPECTION METHOD/LIMITS:
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
ACCESS REQUIRED:
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
REPAIR DESCRIPTION:
____________________________________________________________________________________
____________________________________________________________________________________
____________________________________________________________________________________
COMMENTS:
________________________________________________________________________________________________________________________________________________________________________
____________________________________________________________________________________
Enclose all available data including photos, sketches, etc to:
Cessna Aircraft Company
Attn: CAP Program
Technical Support Servies
Dept. 751
P.O. Box 7706
Wichita, Kansas 67277
FAX 1-316-942-9006
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 26
7/30/2019 CAP 207 Series
27/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
SECTION I - TECHNICAL DOCUMENT REFERENCE
SERVICE MANUALS
Model Number Title
207 & T207(1969 1984) D2060-1-13 207 & T207 Series
To obtain Service Manuals, write to:Cessna Aircraft Company Supply DivisionAtt: SPA Dept
P.O. Box 949Wichita, Kansas 67201Fax 1-316-688-4746
SERVICE BULLETINS
Number Title Date Cap Insp
SE65-83 Aileron Hinge Inspection 9-03-65 57-50-02SE71-4 Improved Nose Gear Steering Collar 2-12-71 32-50-02SE81-1 Gear Warning/Fuel Pump Switch Cable Improvement 1-19-81 32-60-01
SE84-8 Fuel Reservoir Tank Quick Drain Valve Installation 3-16-89 28-30-01SE84-17 Horizontal Stabilizer Aft Attach Bracket 9-28-84 55-10-01SEB85-5 Elevator Trim Tab Actuator Attach Bracket Inspection 3-22-85 27-30-01SEB85-7 Elevator and Trim Tab Inspection 4-05-85 27-30-02SEB85-9 Rear Wing Spar Doubler Inspection. 5-03-85 57-10-05SEB93-4 Upper Left Forward Doorpost Inspection and Modification 3-26-93 53-10-02SEB87-4 Aileron Hinge Attachment 6-12-87 57-50-01SNL85-54 Revised Overhaul/Replacement Requirements for 11-27-85 29-10-01
Hydraulic System Components on Single Engine,Skymaster, and Crusader Airplanes.
SNL86-49 Main Landing Gear Actuator Mounting Bolts 12-12-86 32-30-01
Service Bulletins listed above, write to:Cessna Aircraft Company Supply DivisionDept 753C.P.O. Box 7706Wichita, Kansas 67277Fax 1-316-942-9006
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 27
7/30/2019 CAP 207 Series
28/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
PAGINA INTENCIONALMENTEDEJADO EN BLANCO
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 28
7/30/2019 CAP 207 Series
29/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
SECTION II - LISTING OF 207 SERIES CONTINUED AIRWORTHINESS PROGRAMINSPECTIONS
OB-1001 AO DE FABRICACION 1969 SERIAL NUMBER 20700055OB-1888 AO DE FABRICACION 1974 SERIAL NUMBER 20700266
ContinuedAirworthiness
ProgramInspection
Inspection ComplianceNumber
Title
DateInitial
Effectivity INITIAL REPEAT
27-30-02Elevator Trailing Edge and
Trim Tab Inspections20700001 Thru 20700788
3,000Hrs
3,000Hrs
28-30-01Quick Drain Valves FuelReservoir and Fuel Tanks
20700001 Thru 207007881,000Hrs
or 2 Yrs
1,000 Hrsor 2 Yrs
28-40-01 Fuel Gauging Systems 20700001 Thru 20700788
1,000
Hrsor 3 Yrs
1,000 Hrsor 3 Yrs
29-10-01Hydraulic Hose Replacement
and Hydraulic ComponentReplacement
20700001 Thru 207007885 Yrs or
OnCondition
5 Yrs orOn
Condition
32-50-02Nose Gear Steering Collar
and Upper Torque Link20700001 Thru 20700788
3,000Hrs
3,000Hrs
39-00-01Engine Compartment Wiringand Equipment Installation
20700001 Thru 207007886,000Hrs
or 5 Yrs
2,000Hrs
or 2 Yrs
53-40-01Fuselage Wing Strut Attach
Forging20700001 Thru 20700788
12,000Hrs
1,000Hrs
53-40-02 Fuselage Wing Attachments 20700001 Thru 2070078812,000
Hrs2,000Hrs
53-40-04 Fuselage Vertical FinAttachments
20700001 Thru 20700216 12,000Hrs
2,000Hrs
53-40-06 Main Landing Gear Fittings 20700001 Thru 207007883,000Hrs
1,000Hrs
55-10-01Horizontal Stabilizer Aft Attach
Bracket20700001 Thru 20700788
1,000Hrs
200Hrs
55-30-01Vertical Tail Fin FuselageAttachments
20700001 Thru 2070002112,000
Hrs6,000Hrs
57-10-03
1. 1222105-37 Stiffener -Front Spar Splice LH - Aft2. 0721402-5 Stiffener - FrontSpar Splice LH - Aft.3. 1222105-3 Web - FrontSpar Splice LH - Aft
4. 1222105-5 Web - FrontSpar Splice LH - Fwd5. Strut Attach Hole
20700001 Thru 20700788 15,000Hrs
3,000Hrs
57-10-04
1. 1222005-7 Stiffener FrontSpar Splice LH Aft2. 0721402-5 Stiffener FrontSpar Splice LH Aft3. 1222005-3 Web - FrontSpar Splice LH - Aft4. 1222005-5 Web - FrontSpar Splice LH - Fwd5. Strut Attach Hole
20700001 Thru 2070078815,000
Hrs3,000 Hrs
57-10-06 Wing Fuselage Attach Fittings 20700001 Thru 2070078812,000
Hrs3,000 Hrs
57-10-11 Wing Strut Tube 20700001 Thru 207007881,000Hrs
1,000 Hrs
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 29
7/30/2019 CAP 207 Series
30/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
SECTION III - CONTINUING AIRWORTHINESS PROGRAM INSPECTIONAircraft CESSNA LUGAR:
Model/TypeTotal Time:
Serial Number
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 27-30-02Elevator Trailing Edge and Elevator Trim Tab Inspections
EFFECTIVITY
INSPECTION COMPLIANCE
20700001 Thru 20700788 INITIAL 3,000 HRSREPEAT 3,000 HRS
PURPOSETo direct special attention to the area of the elevator trailing edge and trim tab when inspecting the assemblies.Aircraft operation in coastal regions and high humidity areas are prone to have foam deterioration or corrosion.
INSPECTION INSTRUCTIONS1. When inspecting the elevators, pay particular attention to the elevator trailing edge and elevator trim tab. Evidenceof internal skin to foam separation, soft spots, paint blisters, unsealed edges of exposed foam, foam deterioration orcorrosion are cause for replacement of the assembly.
ACCESS/LOCATION DETECTABLE CRACK SIZEElevator N/A
INSPECTION PROCEDUREVisual
REPAIR/MODIFICATIONNot Applicable
COMMENTSRef.: SEB85-7
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Revision 1: November 1993 (D5121-1-13) 27-30-02
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 30
7/30/2019 CAP 207 Series
31/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 27-30-02
NOTETrailing edge elevator sections are foamfilled on Model 210-Series aircraft. Elevatorskins are corrugated on Model 206-Seriesaircraft.Beginning in 1968, the Model 206 Seriesuses the Model 210 elevator configuration.This change standardizes 200-Series elevatorStabilizer installations.
Elevator Trailing Edge and Elevator Trim Tab InspectionFigure 3-2
Revision 1: November 1993 (D5121-1-13)
27-30-02
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 31
7/30/2019 CAP 207 Series
32/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Aircraft CESSNA LUGAR:
Model/TypeTotal Time:
Serial Number
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 28-30-01
Quick Drain Valves - Fuel Reservoir and Fuel Tanks.
EFFECTIVITYINSPECTION COMPLIANCE
20700001 Thru 20700788 INITIAL 1,000 HRS or 2 YRS
REPEAT 1,000 HRS or 2 YRSThereafter
PURPOSE
To check for possible corrosion.
INSPECTION INSTRUCTIONS1. Remove each fuel reservoir and fuel tank (cell) quick drain and inspect for corrosion. If corrosion appears the
valve must be replaced.2. The reservoir tank should be inspected for internal corrosion also.
ACCESS/LOCATION DETECTABLE CRACK SIZEUnderside of fuselage and wing. N/A
INSPECTION PROCEDUREVisual
REPAIR/MODIFICATIONReplace as required.
COMMENTSRef: SE84-8
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Revision 1: November 1993 (D5121-1-13) 28-30-01
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 32
7/30/2019 CAP 207 Series
33/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 28-30-01
Quick Drain Valves - Fuel Reservoir and Fuel TanksFigure 3-5
Revision 1: November 1993 (D5121-1-13) 28-30-01
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 33
7/30/2019 CAP 207 Series
34/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Aircraft CESSNA LUGAR:
Model/TypeTotal Time:
Serial Number
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 28-40-01Fuel Gaging Systems
EFFECTIVITYINSPECTION COMPLIANCE
20700001 Thru 20700788 INITIAL 1,000 HRS or 3 YRS
REPEAT 1,000 HRS or 3 YRSThereafter
PURPOSEDue to various problems that may occur within the system, the fuel gage may not read empty when the fuel tank is
empty.
INSPECTION INSTRUCTIONS
1. Perform the following inspection every 1000 hours or 3 years or whenever indication of erroneous fuel gagingoperation may occur.
2. De fuel Aircraft.3. Turn master switch on, ensure that the fuel gage reads "0" empty when the tank has only unusable fuel
remaining.
ACCESS/LOCATION DETECTABLE CRACK SIZEWing tank filler port N/A
INSPECTION PROCEDURE
Visual
REPAIR/MODIFICATIONAdjust/replace transmitter and/or gage as required.
COMMENTS
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Revision 1: November 1993 (D5121-1-13) 28-40-01
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 34
7/30/2019 CAP 207 Series
35/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Aircraft CESSNA LUGAR:
Model/TypeTotal Time:
Serial Number
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 29-10-01
Hydraulic Hose Replacement and Hydraulic Component Replacement
EFFECTIVITYINSPECTION COMPLIANCE
20700001 Thru 20700788 INITIAL 5 YRS or ON CONDITION
REPEAT 5 YRS or ON CONDITION
PURPOSE
To ensure that the hydraulic hose and components installed on the airplane are inspected at the proper interval.
INSPECTION INSTRUCTIONS
1. Refer to SNL85-54 (See excerpts under COMMENTS of this CAP.)
ACCESS/LOCATION DETECTABLE CRACK
As required. N/A
INSPECTION PROCEDURE
REPAIR/MODIFICATION
COMMENTS
Refer to SNL85-54.The "on condition" interval applies to -- *
* Brake and landing gear hydraulic system hoses of the later synthetic material (S2178-XXX partnumbers).
* Landing gear hydraulic system power packs used on 1979 and later models (9881124-XX).
* All other components except earlier power packs and hoses of rubber material.
Landing gear power packs used prior to 1979 models still require overhaul every 5 years to replace rubbercomponents. All brake and landing gear hydraulic system hoses used prior to the S2178-XXX part numbers stillrequire replacement every 5 years to replace the rubber hose material.
Revision 1: November 1993 (D5121-1-13) 29-10-01
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 35
7/30/2019 CAP 207 Series
36/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 29-10-01
NOTE
Although part number identification is the positive method to determinehose material, the synthetic hydraulic system hoses generally have a smooth,
somewhat shiny surface texture and are generally a blue or reddish color.Rubber hoses are generally black and have a dull, rougher surface texture.
The new overhaul/replacement requirements will be incorporated in future revisions to the applicable airplane PartsCatalogs and Service Manuals.
The revised requirements in no way preclude the importance of accomplishing thorough hydraulic system inspections,as detailed in the applicable airplane Service Manual. Routine inspections are of the utmost importance to ensurecontinued airworthiness, durability and reliability.
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Revision 1: November 1993 (D5121-1-13) 29-10-01
Aircraft CESSNA LUGAR:
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 36
7/30/2019 CAP 207 Series
37/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Model/TypeTotal Time:
Serial Number
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 32-50-02Nose Gear Steering Collar and Upper Torque Link
EFFECTIVITYINSPECTION COMPLIANCE
20700001 Thru 20700788INITIAL 3,000 HRS
REPEAT * 3,000 HRSThereafter
PURPOSEReports of nose gear steering collar cracking as a result of operations in very rough field conditions.In addition the upper torque link becomes seized in the stop boss area resulting in cracks.
INSPECTION INSTRUCTIONS1. If airplane has been or is operated in rough field conditions, the nose gear steering collar should be inspected in
the area of the stop pin for cracking where the cross sectional area of the collar is reduced.2. Use Dye Penetrant to determine if cracks exist in the steering collar and upper torque link.
ACCESS/LOCATION DETECTABLE CRACK SIZE
Nose Gear If part is cracked, replacementis required.
INSPECTION PROCEDURE* Visual and the use of Dye Penetrant at each 1,000 HR if airplane is being used in rough field operation.
REPAIR/MODIFICATIONRemove and replace with a new steering collar P/N 1243811-6. Refer to specific Model Parts Catalog for specialnotes on additional parts required when installing steering collar.
COMMENTSRef: SE71-4
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Revision 1: November 1993 (D5121-1-13) 32-50-02
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 32-50-02
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 37
7/30/2019 CAP 207 Series
38/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Nose Gear Steering Collar & Upper Torque LinkFigure 3-9 (Sheet 1 of 2)
Revision 1: November 1993 (D5121-1-13) 32-50-02
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 32-50-02
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 38
7/30/2019 CAP 207 Series
39/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Nose Gear Steering Collar & Upper Torque LinkFigure 3-9 (Sheet 2 of 2)
Revision 1: November 1993 (D5121-1-13) 32-50-02
Aircraft CESSNA LUGAR:
Model/Type
Total Time:Serial Number
Registration Fecha Apertura:
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 39
7/30/2019 CAP 207 Series
40/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 39-00-01
Engine Compartment Wiring and Equipment Installation
EFFECTIVITY INSPECTION COMPLIANCE
20700001 Thru 20700788 INITIAL 6,000 HRS or 5 YRS
REPEAT 2,000 HRS or 2 YRSThereafter
PURPOSEPossible deterioration after an extended period of time.
INSPECTION INSTRUCTIONS1. Inspect all wiring, protective sleeving, clamps, supports, etc. for signs of deterioration due to heat, abrasion
vibration, etc.2. Assure that all wiring is properly supported and is secured in such a manner as not to come in contact with sharp
edges of sheet metal parts, engine controls or engine components that operate at elevated temperatures.3. Inspect all electrical grounds at the firewall for security and corrosion.4. Assure that voltage regulators or alternator control units mounted on the firewall are free of corrosion and are
properly grounded. (Remove bolts and clean.)5. Assure that terminals of sender units on engine are secure and the wiring is free of damage from heat or
abrasion.6. Assure that engine is properly grounded to the airframe.
ACCESS/LOCATION DETECTABLE CRACK SIZERemove engine cowling N/A
INSPECTION PROCEDUREVisual
REPAIR/MODIFICATION
COMMENTS
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Revision 1: November 1993 (D5121-1-13) 39-00-01
Aircraft CESSNA LUGAR:
Model/TypeTotal Time:
Serial Number
Registration Fecha Apertura:
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 40
7/30/2019 CAP 207 Series
41/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 53-40-01
Fuselage Wing Strut Attach Forging
EFFECTIVITYINSPECTION COMPLIANCE
20700001 Thru 20700788INITIAL 12,000 HRSREPEAT 3,000 HRS
ThereafterPURPOSETo check for possible cracks radiating out of wing strut attach holes and rivet holes attaching end fittings to the struttube. Also, check for loose and working fasteners in forging attachment.
INSPECTION INSTRUCTIONS1. Inspect wing strut attach forging for cracks.2. Visually inspect for loose and working fasteners.3. Eddy Current inspect per instructions in Section 4-0, Basic Information, pages x and xi
ACCESS/LOCATION DETECTABLE CRACK SIZESupport wing and remove strut and fairings. Strut attach hole No Cracks.
Surrounding area - 0.060 detectable cracks.
INSPECTION PROCEDUREEddy Current strut attach hole. Visually inspect remaining areas of the strut attach forging for cracks, loose andworking fasteners.
REPAIR/MODIFICATIONReplace wing strut attach forging if crack(s) radiate out from the attach hole. Contact Cessna for repair of theremaining areas.
COMMENTSReport any cracks or loose/working fasteners to Cessna Aircraft Company.
Should any history of low level overland survey or patrol exist then the initial eddy current inspection and interval shallbe half of the hours listed above.
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Temporary Revision Number 1 (D5121-1-13) 53-40-01July 15, 1998
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 53-40-01
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 41
7/30/2019 CAP 207 Series
42/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Revision 1: November 1993 (D5121-1-13) 53-40-01
Aircraft CESSNA LUGAR:Model/Type Total Time:
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 42
Fuselage Wing Strut Attach
Forging Figure 3-13
7/30/2019 CAP 207 Series
43/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Serial Number
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 53-40-02
Fuselage Wing Attachments
EFFECTIVITYINSPECTION COMPLIANCE
20700001 Thru 20700788INITIAL 12,000 HRSREPEAT 2,000 HRS
ThereafterPURPOSETo inspect wing attach fitting for damage.
INSPECTION INSTRUCTIONS1. Inspect wing attach fittings and their adjacent supporting structure.2. Replace cracked wing attach and fitting bolts.3. Eddy Current inspect per instructions in Section 4-0, Basic Information, pages x and xi.
ACCESS/LOCATION DETECTABLE CRACK SIZE
Remove wing-to-fuselage fairings. N/A
INSPECTION PROCEDUREEddy Current
REPAIR/MODIFICATIONIf cracks are found, contact Cessna Aircraft Company and describe condition.
COMMENTS
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Temporary Revision Number 1 (D5121-1-13) 53-40-02July 15, 1998
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 53-40-02
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 43
7/30/2019 CAP 207 Series
44/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Fuselage Wing AttachmentsFigure 3-14
Revision 1: November 1993 (D5121-1-13) 53-40-02
Aircraft CESSNA LUGAR:
Model/Type Total Time:
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 44
7/30/2019 CAP 207 Series
45/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Serial Number
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 53-40-04
Fuselage Vertical Fin Attachments
EFFECTIVITYINSPECTION COMPLIANCE
20700001 Thru 20700216INITIAL 12,000 HRSREPEAT 2,000 HRS
ThereafterPURPOSE
Structural Testing.
INSPECTION INSTRUCTIONS
1. Visually inspect Sta. 209/239 forward bulkhead and Sta. 230/260 aft bulkhead in the area of the vertical fin sparattachment.
2. Dye Penetrant inspect rudder cable cutouts in Sta. 230/260 aft bulkhead and Sta. 209/239 forward bulkhead.3. Dye Penetrant inspect the upper corners of Sta. 230/260 bulkhead that contain the aft horizontal tail attachment.
ACCESS/LOCATION DETECTABLE CRACK SIZE
Remove vertical fin-to-horizontal tail fairings. Remove stinger 0.06 Inch.Sta 209/239 fwd bulkhead and Sta. 230/260 aft bulkhead.
INSPECTION PROCEDUREVisual and Dye Penetrant
REPAIR/MODIFICATIONContact Cessna and define extent of damage.
COMMENTS
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Revision 1: November 1993 (D5121-1-13) 53-40-04
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 53-40-04
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 45
7/30/2019 CAP 207 Series
46/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Fuselage Vertical Fin AttachmentsFigure 3-16 (Sheet 1 of 4)
Revision 1: November 1993 (D5121-1-13) 53-40-04
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 46
7/30/2019 CAP 207 Series
47/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Revision 1: November 1993 (D5121-1-13) 53-40-04
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 53-40-04
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 47
Fuselage Vertical Fin AttachmentsFigure 3-16 (Sheet 2 of 4)
7/30/2019 CAP 207 Series
48/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Revision 1: November 1993 (D5121-1-13) 53-40-04
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 53-40-04
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 48
Fuselage Vertical Fin AttachmentsFigure 3-16 (Sheet 3 of 4)
7/30/2019 CAP 207 Series
49/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Revision 1: November 1993 (D5121-1-13) 53-40-04
Aircraft CESSNA LUGAR:Model/Type Total Time:
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 49
Fuselage Vertical Fin AttachmentsFigure 3-16 (Sheet 4 of 4)
7/30/2019 CAP 207 Series
50/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Serial Number
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 53-40-06
Main Landing Gear Support Fittings
EFFECTIVITYINSPECTION COMPLIANCE
20700001 Thru 20700788 INITIAL 3,000 HRS
REPEAT 1,000 HRSThereafter
PURPOSEOutboard forging has experienced cracking in service.
INSPECTION INSTRUCTIONS1. Visually inspect both inboard and outboard main landing gear support forgings for cracks in radiuses areas or
cracks propagating out of holes in attachment flanges.
ACCESS/LOCATION DETECTABLE CRACK SIZERemove fuselage to main landing gear spring fairing and floorboard N/Ainspection plate between the main landing gear and inboard forgings.Location/Outboard and inboard MLG support forgings.
INSPECTION PROCEDURE
Visual
REPAIR/MODIFICATION
Replace
COMMENTS
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Revision 1: November 1993 (D5121-1-13) 53-40-06
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 53-40-06
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 50
7/30/2019 CAP 207 Series
51/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Main Landing Gear Support ForgingsFigure 3-18
Revision 1: November 1993 (D5121-1-13) 53-40-06
Aircraft CESSNA LUGAR:Model/Type Total Time:
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 51
7/30/2019 CAP 207 Series
52/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Serial Number
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 55-10-01
Horizontal Stabilizer Aft Attach Bracket
EFFECTIVITYINSPECTION COMPLIANCE
20700001 Thru 20700788INITIAL 1,000 HRS
REPEAT 200 HRSThereafter
PURPOSECracking has been experienced in the radius areas and the attach points of the bracket flanges on several high timeairplanes.Ref.: SE84-17, FAA AC 43-16 Number 61, Aug. 1983.FAA AC. 43-16 Number 79, Feb. 1985.
FAA AC. 43-16 Number 27, Oct. 1980.FAA AC. 43-16 Number 15, Oct. 1979.
INSPECTION INSTRUCTIONS
Visually inspect the stabilizer aft spar attach bracket per SE84-17.
ACCESS/LOCATIONDETECTABLE CRACK SIZE
Remove horizontal stabilizer-to-fuselage fairings and stinger. N/A
INSPECTION PROCEDUREVisual
REPAIR/MODIFICATIONReplacement Per SE 84-17
COMMENTS
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Revision 1: November 1993 (D5121-1-13) 55-10-01
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 55-10-01
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 52
7/30/2019 CAP 207 Series
53/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
IMPROVED STEEL BRACKETS (P/N 1232624-1) ARE AVAILABLEFOR THE FOLLOWING SERIALS:20700001 Thru 20700784 (1969 Thru 1984)U206-0915 Thru U20606832 (1968 Thru 1984)
Horizontal Stabilizer Attach BracketFigure 3-19
Revision 1: November 1993 (D5121-1-13) 55-10-01
Aircraft CESSNA LUGAR:
Model/TypeTotal Time:Serial Number
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 53
7/30/2019 CAP 207 Series
54/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 55-30-01
Vertical Tail Fin Fuselage Attachments
EFFECTIVITYINSPECTION COMPLIANCE
20700001 Thru 20700021 INITIAL 12,000 HRSREPEAT 6,000 HRS
Thereafter
PURPOSEStructural Testing.
INSPECTION INSTRUCTIONS1. Visually inspect Sta. 209/239 forward fin spar attachment and Sta. 230/260 aft fin spar attachments.2. Dye Penetrant inspect rear spar outboard flanges on inside surface (just above Sta. 230/260 aft bulkhead) at the
lower fwd skin attach rivet holes.
ACCESS/LOCATION DETECTABLE CRACK SIZE
Remove vertical fin-to-horizontal tail fairings. 0.012 Inch.Remove stinger.Sta. 209/239 fwd bulkhead fin spar attachment andSta. 230/260 aft bulkhead fin spar attachment.
INSPECTION PROCEDUREVisual and Dye Penetrant
REPAIR/MODIFICATION
Contact Cessna Aircraft Company and define extent of damage.
COMMENTS
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Revision 1: November 1993 (D5121-1-13) 55-30-01
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 55-30-01
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 54
7/30/2019 CAP 207 Series
55/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Revision 1: November 1993 (D5121-1-13) 55-30-01
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 55-30-01
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 55
AFN FIN SPAR ATTACHMENTVertical Tail Fin Fuselage Attachments
Figure 3-20 (Sheet 1 of 5)
7/30/2019 CAP 207 Series
56/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Revision 1: November 1993 (D5121-1-13) 55-30-01
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS : 55-30-01
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 56
Vertical Tail Fin Fuselage AttachmentsFigure 3-20 (Sheet 2 of 5)
7/30/2019 CAP 207 Series
57/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Vertical Tail Fin Fuselage AttachFigure 3-20(Sheet 3 of 5)
Revision 1: November 1993 (D5121-1-13) 55-30-01
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 55-30-01
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 57
7/30/2019 CAP 207 Series
58/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Vertical Tail Fin Fuselage AttachmentsFigure 3-20(Sheet 4 of 5)
Revision 1: November 1993 (D5121-1-13) 55-30-01
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 55-30-01
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 58
7/30/2019 CAP 207 Series
59/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Vertical Tail Fin Fuselage AttachmentsFigure 3-20(Sheet 5 of 5)
Revision 1: November 1993 (D5121-1-13) 55-30-01
Aircraft CESSNA LUGAR:
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 59
7/30/2019 CAP 207 Series
60/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Model/TypeTotal Time:
Serial Number
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 57-10-031. 1222105-37 Stiffener - Front Spar Splice LH - Aft2. 0721402-5 Stiffener - Front Spar Splice LH - Aft3. 1222105-3 Web - Front Spar Splice LH - Aft4. 1222105-5 Web - Front Spar Splice LH - Fwd5. Strut Attach Hole
EFFECTIVITYINSPECTION COMPLIANCE
20700001 Thru 20700788INITIAL 15,000 HRS*REPEAT 3,000 HRS *
PURPOSEStructural Testing.
INSPECTION INSTRUCTIONS1. Eddy Current Inspect the cross-section of the front spar stiffener angle the complete length (6).
(Refer to step 6 for Eddy Current equipment.)2. Eddy Current Inspect the cross-section of the front spar stiffener cap angle the complete length (1).
(Refer to step 6 for Eddy Current equipment.)3. Eddy Current Inspect the lower 1/3 cross-section of the web splice the complete length (2).
(Refer to step 6 for Eddy Current equipment.)4. Eddy Current Inspect the lower 1/3 cross-section or web splice the complete length (3).
(Refer to step 6 for Eddy Current equipment.)5. Eddy Current Inspect strut attach hole. (Refer to step 6 for Eddy Current equipment.)6. Eddy Current inspect per instructions in Section 4-0, Basic Information, pages x and xi.
ACCESS/LOCATION DETECTABLE CRACK SIZEW.S. 100 inspection plates - inspect both wings. 1, 2, 3, & 4 - .12 Inch.Support wing and remove strut. 5 - .06 Inch.
INSPECTION PROCEDUREEddy Current
REPAIR/MODIFICATIONRemove and replace.
COMMENTS
Report any cracks to Cessna.* Should any history of low level overland survey and patrol exist then the initial inspection compliance is 8000 hrs.and at 1500 hour intervals thereafter.
Temporary Revision Number 1 (D5121-1-13) 57-10-03July 15, 1998
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 57-10-02
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 60
7/30/2019 CAP 207 Series
61/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
NOTE: REMOVE INSPECTIONPLATE FOR CLARITY
Wing Station 100 Splice Inspection AreaFigure 3-22
Revision 1: November 1993 (D5121-1-13) 57-10-02
Aircraft CESSNA LUGAR:
Model/TypeTotal Time:Serial Number
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 61
7/30/2019 CAP 207 Series
62/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 57-10-04
1. 1222005-7 Stiffener - Front Spar Splice LH - Aft2. 0721402-5 Stiffener - Front Spar Splice LH - Aft3. 1222005-3 Web - Front Spar Splice LH - Aft4. 1222005-5 Web - Front Spar Splice LH - Fwd5. Strut Attach Hole
EFFECTIVITY INSPECTION COMPLIANCE
20700001 Thru 20700788 INITIAL 15,000 HRS*
REPEAT 3,000 HRS *
PURPOSE
Structural Testing.
INSPECTION INSTRUCTIONS1. Eddy Current Inspect the cross-section of the front spar stiffener angle the complete length (6).
(Refer to step 6 for Eddy Current equipment.)2. Eddy Current Inspect the cross-section of the front spar stiffener cap angle the complete length (1).
(Refer to step 6 for Eddy Current equipment.)3. Eddy Current Inspect the lower 1/3 cross-section of the web splice the complete length (2).
(Refer to step 6 for Eddy Current equipment.)4. Eddy Current Inspect the lower 1/3 cross-section or web splice the complete length (3).
(Refer to step 6 for Eddy Current equipment.)5. Eddy Current Inspect strut attach hole. (Refer to step 6 for Eddy Current equipment.)6. Eddy Current inspect per instructions in Section 4-0, Basic Information, pages x and xi.
ACCESS/LOCATION DETECTABLE CRACK SIZE
W.S. 100 inspection plates - inspect both wings. 1, 2, 3, & 4 - 0.12 Inch.Support wing and remove strut. 5 - 0.06 Inch.
INSPECTION PROCEDUREEddy Current and/or Radiographic
REPAIR/MODIFICATIONRemove and replace.
COMMENTS
Report any cracks to Cessna.* Should any history of low level overland survey and patrol exist then the initial inspection compliance is 8,000 hrs.and at 1,500 hour intervals thereafter.
Temporary Revision Number 1 (D5121-1-13) 57-10-04July 15, 1998
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 57-10-04
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 62
7/30/2019 CAP 207 Series
63/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
NOTE: WITH THE ADDITION OF ITEM (6) THE FIRST SIGNIFICANT TESTSPECIMEN CRACKS WERE LOCAL SKIN CRACKING(5) AND A CRACK IN ITEM (6)
(CRACKS NOT SHOWN IN ITEMS 5 AND 6).
Wing Station 100 Splice Inspection AreaFigure 3-24
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Revision 1 : November 1993 (D5121-1-13) 57-10-04
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 63
7/30/2019 CAP 207 Series
64/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Aircraft CESSNA LUGAR:
Model/TypeTotal Time:
Serial Number
Registration Fecha Apertura:
TITLE CONTINUED AIRWORTHINESS INSPECTION NUMBER: 57-10-06
Wing Fuselage Attach Fittings
EFFECTIVITYINSPECTION COMPLIANCE
20700001 Thru 20700788INITIAL 12,000 HRSREPEAT 3,000 HRS
Thereafter
PURPOSEPrimary load path.No known history of cracking except for rear spar web referred to in CAP Item 57-10-05.
INSPECTION INSTRUCTIONS1. Inspect for possible cracking from wing attachment holes outward, (Refer to step 4.).2. Possible galling or deformation of wing attachment holes, (Refer to step 4.).3. Do not remove wing attach bolts unless cracking or looseness suspected, (Refer to step 4.).4. Eddy Current inspect per instructions in Section 4-0, Basic Information, pages x and xi.
ACCESS/LOCATION DETECTABLE CRACK SIZERemove wing-to-fuselage fairing strips. N/A
INSPECTION PROCEDUREEddy Current
REPAIR/MODIFICATIONRear Spar Kits Available - Refer to Service Bulletin List in Section I.
COMMENTS
Replace cracked parts.Contact Cessna Aircraft Company for instructions on oversize holes.
Temporary Revision Number 1 (D5121-1-13) 57-10-06July 15, 1998
CONTINUING AIRWORTHINESS PROGRAM INSPECTIONS: 57-10-06
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 64
7/30/2019 CAP 207 Series
65/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
Wing Fuselage Attach FittingsFigure 3-26
REMARK COMPLIANCE:
FECHA DE CUMPLIMIENTO ..
MECANICO INSPECTOR
Revision 1: November 1993 (D5121-1-13) 57-10-06
Aircraft CESSNA LUGAR:
Model/Type
Total Time:Serial Number
Registration Fecha Apertura:
FECHA: 08-ABRIL-2010 REVISION: ORIGINAL PAGINA: 65
7/30/2019 CAP 207 Series
66/67
7/30/2019 CAP 207 Series
67/67
CAPMODEL 207 SERIES
SUPLEMENTO DEL PMA CONTINUED AIRWORTHINESS PROGRAM
PAGINA INTENCIONALMENTE
DEJADO EN BLANCO