PARÁMETRO DE CONFIGURACIÓN DEL SISTEMA

8/2/2019 PARMETRO DE CONFIGURACIN DEL SISTEMA

1/5

Localizacin y Solucin de Pr oblem asC27 and C32 Engines for Cate rpil lar Built Machines

System Configuration Parameters

SMCS - 1901

System configuration parameters are parameters that are configured to specify the engine's emissionslevels, the power rating, and the specific application. Default values for the parameters are programmedat the factory. Some parameters may be changed in order to equip the engine for a specific application.The system configuration parameters must be reprogrammed if the Electronic Control Module (ECM) isreplaced. It is not necessary to reprogram the system configuration parameters if you update the ECMflash file. Certain configuration parameters are stamped into the engine information plate.

Note: If the parameters that are protected with the factory passwords are changed, the Caterpillarwarranty may be voided.

Parameter Descriptions

Equipment ID

The "Equipment ID" parameter allows the customer to enter a description into the ECM in order toidentify the engine's application. A maximum of 17 characters can be entered in the field.

Engine Serial Number

Program the "Engine Serial Number" to match the engine serial number that is stamped on the engine

information plate. The engine serial number is not preprogrammed on a replacement ECM.

ECM Part Number

This parameter identifies the part number for the ECM.

ECM Serial Number

This parameter identifies the serial number for the ECM.

Cerrar SIS

Pantalla anterior

Producto: TRUCKModelo: 777F TRUCK JRP

Configuracin: 777F Off-Highway Truck JRP00001-UP (MACHINE)POWERED BY C32 Engine

Nmero de medio -RENR9346-0 3 Fecha de pub licacin -01 / 08 / 2007 Fecha de actua l izacin -07 / 08 / 2007

i02529692

Page 1 of 5777F Off-Highway Truck JRP00001-UP (MACHINE) POWERED BY C32 Engine(SEB...

20-08-2008https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw ...


2/5

Software Group Part Number

This parameter identifies the part number of the flash file that is currently installed in the ECM.

Software Group Release Date

This parameter identifies the release date of the flash file that is currently installed in the ECM.

Software Group Description

This parameter identifies the description of the application for the flash file that is currently installed inthe ECM.

Full Load Setting (FLS)

FLS is a parameter that represents the adjustment to the fuel system that was made at the factory in orderto fine tune the fuel system. The correct value for this parameter is stamped on the engine information

plate. Only change this value if the engine is rerated or if a new ECM has been installed. Factorypasswords are required to change this parameter.

Full Torque Setting (FTS)

FTS is similar to FLS. Only change this value if the engine is rerated or if a new ECM has beeninstalled. Factory passwords are required to change this parameter.

Rated Power

This parameter specifies the rated power of the engine.

Rated Peak Torque

This parameter specifies the rated peak torque of the engine.

Top Engine Speed Range

This parameter specifies the maximum speed setting for the engine.

Test Spec

This is the engine's "Test Specifiction Number". Use this number to retrieve data that is related to theengine's specifications from the Technical Marketing Information System (TMI). The followinginformation can be retrieved from TMI:

"As shipped consists"

"Engine test specifications"

"Systems data"




3/5

"Physical data"

"Gasket kit data"

"Reman parts"

"Performance data"

A link to TMI Web can be found on the web site for the Service Information System (SIS).

Total Tattletale

The total tattletale counts the number of changes to system parameters.

Ether Solenoid Configuration

This parameter is enabled in order to define the installation status of an ether starting aid for the engine.

Engine Retarder Enable Command (Option)

This parameter is enabled in order to define the installation status of compression brakes for the engine.

Parameter Table

Table 1

System Configuration Parameters

Parameter Available Range orOptions

Default RequiredPassword

Configuration Group 1

Equipment ID17 alphanumericcharacters

Blank None

ECM Identification Parameters

Engine Serial Number0XX00000 orXXX00000

Blank Factory

ECM Serial Number Hardware Dependent Blank Read Only (1)

ECM Part Number Hardware Dependent Blank Read Only (1)

Software Group Part Number Software Dependent Read Only (1)

Software Group Release Date Software Dependent Read Only (1)

Software Group Description Software Dependent Read Only (1)




4/5

Parameter Worksheet

Record the following information before you change any programmable parameter.

System Parameters

FLS Programmed at the Factory Factory

FTS Programmed at the Factory Factory

Rated Power Software Dependent Read Only (1)

Rated Peak Torque Software Dependent Read Only (1)

Top Engine Speed Range Software Dependent Read Only (1)

Test Spec Software Dependent Read Only (1)

Total Tattletale 0 to 65535 0 Read Only (1)

Engine Configuration Parameters

Ether Solenoid ConfigurationNot InstalledContinuous Flow

Solenoid

Continuous Flow

Solenoid

None

Engine Fan ControlOnOff

Off None

Engine Retarder EnableCommand (Option)

EnabledDisabled

Disabled None

( 1 ) This parameter can be viewed only. No changes are allowed.

Table 2

Engine Parameters

Equipment ID


ECM Serial Number

ECM Part Number

Software Group Part Number




5/5

Note: Compare the FLS and the FTS from the ECM with the values that are listed on the engineinformation plate. Use of incorrect parameters could cause damage to the engine. Use of the incorrectparameters may also void the Caterpillar warranty or the emission certification for the engine.

Software Group Release Date

Total Tattletale

FLS

FTS

Ether Solenoid Configuration

Engine Fan Control

Engine Retarder Enable Command

Table 3

Information From Engine Information Plate


FLS

FTS

Copyright 1993 - 2008 Caterpillar Inc.Todos los derechos reservados.

Red privada para licenciados del SIS.

Wed Aug 20 14:30:35 UTC-0400 2008


20 08 2008h // i / i b/ i b/ hd / hd i j ? l / i b/ i

PARÁMETRO DE CONFIGURACIÓN DEL SISTEMA

Documents

Transcript of PARÁMETRO DE CONFIGURACIÓN DEL SISTEMA