8/2/2019 PARMETRO DE CONFIGURACIN DEL SISTEMA
1/5
Localizacin y Solucin de Pr oblem asC27 and C32 Engines for Cate rpil lar Built Machines
System Configuration Parameters
SMCS - 1901
System configuration parameters are parameters that are configured to specify the engine's emissionslevels, the power rating, and the specific application. Default values for the parameters are programmedat the factory. Some parameters may be changed in order to equip the engine for a specific application.The system configuration parameters must be reprogrammed if the Electronic Control Module (ECM) isreplaced. It is not necessary to reprogram the system configuration parameters if you update the ECMflash file. Certain configuration parameters are stamped into the engine information plate.
Note: If the parameters that are protected with the factory passwords are changed, the Caterpillarwarranty may be voided.
Parameter Descriptions
Equipment ID
The "Equipment ID" parameter allows the customer to enter a description into the ECM in order toidentify the engine's application. A maximum of 17 characters can be entered in the field.
Engine Serial Number
Program the "Engine Serial Number" to match the engine serial number that is stamped on the engine
information plate. The engine serial number is not preprogrammed on a replacement ECM.
ECM Part Number
This parameter identifies the part number for the ECM.
ECM Serial Number
This parameter identifies the serial number for the ECM.
Cerrar SIS
Pantalla anterior
Producto: TRUCKModelo: 777F TRUCK JRP
Configuracin: 777F Off-Highway Truck JRP00001-UP (MACHINE)POWERED BY C32 Engine
Nmero de medio -RENR9346-0 3 Fecha de pub licacin -01 / 08 / 2007 Fecha de actua l izacin -07 / 08 / 2007
i02529692
Page 1 of 5777F Off-Highway Truck JRP00001-UP (MACHINE) POWERED BY C32 Engine(SEB...
20-08-2008https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw ...
8/2/2019 PARMETRO DE CONFIGURACIN DEL SISTEMA
2/5
Software Group Part Number
This parameter identifies the part number of the flash file that is currently installed in the ECM.
Software Group Release Date
This parameter identifies the release date of the flash file that is currently installed in the ECM.
Software Group Description
This parameter identifies the description of the application for the flash file that is currently installed inthe ECM.
Full Load Setting (FLS)
FLS is a parameter that represents the adjustment to the fuel system that was made at the factory in orderto fine tune the fuel system. The correct value for this parameter is stamped on the engine information
plate. Only change this value if the engine is rerated or if a new ECM has been installed. Factorypasswords are required to change this parameter.
Full Torque Setting (FTS)
FTS is similar to FLS. Only change this value if the engine is rerated or if a new ECM has beeninstalled. Factory passwords are required to change this parameter.
Rated Power
This parameter specifies the rated power of the engine.
Rated Peak Torque
This parameter specifies the rated peak torque of the engine.
Top Engine Speed Range
This parameter specifies the maximum speed setting for the engine.
Test Spec
This is the engine's "Test Specifiction Number". Use this number to retrieve data that is related to theengine's specifications from the Technical Marketing Information System (TMI). The followinginformation can be retrieved from TMI:
"As shipped consists"
"Engine test specifications"
"Systems data"
Page 2 of 5777F Off-Highway Truck JRP00001-UP (MACHINE) POWERED BY C32 Engine(SEB...
20-08-2008https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw ...
8/2/2019 PARMETRO DE CONFIGURACIN DEL SISTEMA
3/5
"Physical data"
"Gasket kit data"
"Reman parts"
"Performance data"
A link to TMI Web can be found on the web site for the Service Information System (SIS).
Total Tattletale
The total tattletale counts the number of changes to system parameters.
Ether Solenoid Configuration
This parameter is enabled in order to define the installation status of an ether starting aid for the engine.
Engine Retarder Enable Command (Option)
This parameter is enabled in order to define the installation status of compression brakes for the engine.
Parameter Table
Table 1
System Configuration Parameters
Parameter Available Range orOptions
Default RequiredPassword
Configuration Group 1
Equipment ID17 alphanumericcharacters
Blank None
ECM Identification Parameters
Engine Serial Number0XX00000 orXXX00000
Blank Factory
ECM Serial Number Hardware Dependent Blank Read Only (1)
ECM Part Number Hardware Dependent Blank Read Only (1)
Software Group Part Number Software Dependent Read Only (1)
Software Group Release Date Software Dependent Read Only (1)
Software Group Description Software Dependent Read Only (1)
Page 3 of 5777F Off-Highway Truck JRP00001-UP (MACHINE) POWERED BY C32 Engine(SEB...
20-08-2008https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw ...
8/2/2019 PARMETRO DE CONFIGURACIN DEL SISTEMA
4/5
Parameter Worksheet
Record the following information before you change any programmable parameter.
System Parameters
FLS Programmed at the Factory Factory
FTS Programmed at the Factory Factory
Rated Power Software Dependent Read Only (1)
Rated Peak Torque Software Dependent Read Only (1)
Top Engine Speed Range Software Dependent Read Only (1)
Test Spec Software Dependent Read Only (1)
Total Tattletale 0 to 65535 0 Read Only (1)
Engine Configuration Parameters
Ether Solenoid ConfigurationNot InstalledContinuous Flow
Solenoid
Continuous Flow
Solenoid
None
Engine Fan ControlOnOff
Off None
Engine Retarder EnableCommand (Option)
EnabledDisabled
Disabled None
( 1 ) This parameter can be viewed only. No changes are allowed.
Table 2
Engine Parameters
Equipment ID
Engine Serial Number
ECM Serial Number
ECM Part Number
Software Group Part Number
Page 4 of 5777F Off-Highway Truck JRP00001-UP (MACHINE) POWERED BY C32 Engine(SEB...
20-08-2008https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw ...
8/2/2019 PARMETRO DE CONFIGURACIN DEL SISTEMA
5/5
Note: Compare the FLS and the FTS from the ECM with the values that are listed on the engineinformation plate. Use of incorrect parameters could cause damage to the engine. Use of the incorrectparameters may also void the Caterpillar warranty or the emission certification for the engine.
Software Group Release Date
Total Tattletale
FLS
FTS
Ether Solenoid Configuration
Engine Fan Control
Engine Retarder Enable Command
Table 3
Information From Engine Information Plate
Engine Serial Number
FLS
FTS
Copyright 1993 - 2008 Caterpillar Inc.Todos los derechos reservados.
Red privada para licenciados del SIS.
Wed Aug 20 14:30:35 UTC-0400 2008
Page 5 of 5777F Off-Highway Truck JRP00001-UP (MACHINE) POWERED BY C32 Engine(SEB...
20 08 2008h // i / i b/ i b/ hd / hd i j ? l / i b/ i
Top Related