Ajuste Puente Ibanez
-
Upload
jpatologico -
Category
Documents
-
view
213 -
download
0
Transcript of Ajuste Puente Ibanez
-
7/31/2019 Ajuste Puente Ibanez
1/2
INSTRUCTION MANUAL
E L E C T R I C B A S S E S
STRING GAUGESIbanez basses are factory equipped with the following string gauges.
MONO-RAIL
Mono-Rail bridges allow the bass strings to beisolated from one another by usingindependent bridge plates for each string. Thesaddles are locked on the base plates. To
adjust the saddle, loosen the saddle lockscrews (A) before adjustment.After adjustment, lock the saddle lock screws(A). Loosen the string before loosening thesaddle lock down screw (A).The D-tuner allows the user to drop thestrings pitch by raising the lever. The dropnote can be adjusted by turning the D-Tune adjustment screw (B) at theback of the bridge while the D-tuner lever is pulled up.Loosen the lock nut (C) by the hexagonal wrench included. Then, turn theadjustment screw (B) to obtain your preferred pitch. For higher pitch,turn the screw clockwise, the other way for lower pitch.
MODELS STRING GAUGES
4 STRING .045-.095
5 STRING .045-.095 + .125
6 STRING .035-.045 + .095 + .125
35 SCALE 4 STRING .045-.105
35 SCALE 5 STRING .045-.105 + .135
*When replacing strings, check with the dealer to make sure the new strings are longenough for the full scale length of the bass.
MONO-RAIL IIMono-Rail II bridges allow the bass strings to beisolated from one another by using independentbridge plates for each string. The strings areinstalled by lowering the ball end into the bridge
and hooking the ballend below the stringcatch at the rear ofthe bridge.Intonation adjustments can be made byadjusting the intonation screws (A) at the rearof the bridge clockwise to move the saddleback, and counter clockwise to move thesaddle forward.
ACCU-CAST B20, B25The ACCU-CAST bass bridge was designed foreasy string change, durability, and accuratestring height adjustment. To raise of the lowerthe string action, insert the correct Allenwrench into the screw (A) at the saddle. Toraise the saddle turn the wrench clockwise andto lower the saddle turn the wrench counterclockwise.Intonation adjustments can be made by adjusting the intonation screws(B) at the rear of the bridge clockwise to move the saddle back andcounter clockwise to move the saddle forward.
ATK
ATK bridges were designed to allow themaximum amount of string vibration to
transfer from the body. For slightly moresustain, strings can be installed either fromthe back of the instrument through thestring grommets. For slightly more attack,the strings can be lowered into the bridgefrom the front of the instrument and
hooked onto thestring catch. Intonation adjustments can bemade by adjusting the intonation screws (A) atthe rear of the bridge clockwise to move thesaddle back, and counter clockwise to movethe saddle forward.
*Note: When replacing string check with the dealer tomake sure the new strings are long enough for the fullscale length of the bass.
STANDARD BRIDGE
To replace strings, thread the new stringsthrough the string holes located on the back ofthe tailpiece and bring them up and over thesaddle. The intonation can be adjusted bymoving the saddle forward or backward usinga Phillips head (+) screwdriver on theadjustment screw at the rear of the bridge.String height is controlled by using a wrenchto raise or lower the small Allen screws oneither side of the saddle.
Printed in Japan MAR00317 Copyright 2000
This is to certify that the aforementioned equipments fully conform to
protection requirements of the following EC council directives.
DIRECTIVES : 89/336/EEC Electromagnetic compatibility
DISTRIBUTED BY
(A)
(B)
(C)
(A)
(A)(B)
(A)
-
7/31/2019 Ajuste Puente Ibanez
2/2
PICKUP SELECTION
ALL 2 PICKUP MODELS : PICKUP BALANCERThe pickup balance control pot allows theuser to blend between the front and backpickups using a single pot. The centerposition of the pot has a de-tent which willset both pickups to equal output.Turning the knob clockwise increases theneck pickup while decreasing the output ofthe bridge pickup. Turning the knob counterclockwise decreases the neck pickup andincreases the output of the bridge pickup.
ACTIVE EQ.
CONTROLS
SR SERIES (AFR-P, J PICKUP MODELS) : VARI-MIDThe Vari-Mid was designed for use with active pickups and allows theuser to custom-tailor the frequency response of the mid- range. Tunable
mid range is a unique Ibanez bass feature that allows tonal variationsnot achievable on a standard 3 band EQ.
SR SERIES (SFR PICKUP MODELS) : VARI-MID HIFIThe Vari-Mid Hi-Fi EQ system was designed to work with passive pickupswhile incorporating Ibanez sweepable mid-range technology.
BTB SERIES : VARI-MID 3BThe Vari-Mid 3B EQ was designed to work with passive pickups and isloaded with 18 volts to allow the user to get more output from the bassbefore distortion.
Volume
Balancer
Mid Boost/Cut
Mid Frequency
Treble Boost/CutBass Boost/Cut
Mid Boost/Cut
Balancer
Volume
Treble Boost/Cut
Bass Boost/Cut
Mid Frequency
Volume w/Gain Boost Sw.Pull:Boost
Bass Boost/Cut
Mid Boost/Cut
Balancer
Treble Boost/Cut
SR : VARI-MID BTB : VARI-MID 3way PU Character Sw.ATK1300/5way PU Selecter
Volume
Treble Boost/Cut
Mid Boost/CutBass Boost/Cut
ATK
Balancer
VolumeBass Boost/Cut
Treble Boost/Cut
EQB II
VWB
Volume w/EQ Bypass Sw.Pull:Bypass
Treble
Bass
GWB
Balancer
Volume
Bass Boost/Cut
Treble Boost/Cut
DWB
BRIDGEPICKUP
NECKPICKUP
ATK : 5 WAY PICKUP CHARACTER SWITCHThe 5 way pickup character switchallows the user five completelydifferent tone positions.
VARI-MID EQ VWB : EQB-VW The EQB-VW three band EQfeatures a specially tunedmidrange control which allows forradical tone shaping. Pulling onthe volume control kicks in a gainboost circuit for additional volumeand punch. A trim pot inside thecontrol cavity can adjust theamount of gain.
DWB : EQB-DWThe EQB-DW active two band EQoffers versatility with very simpleoperation.
ATK : 3 BAND EQThe Ibanez EQB-3 was designedfor use with passive pickups andallows the user to control thebass/treble and mid range boostand cut.
Neck Center Bridge